Proposal to ensure that all replacement pollution control devices conform with the intent of UN R49 and to align UN R49 in this regard with Regulation (EU) 2016/1718. CLEPA proposes the establishment of a new annex under UN R49-05 R.49-05 to restrict the approval of a replacement device to one that “enables the engine and vehicle to comply with the rules with which it was originally in compliance”.

European Commission report on the effort to transpose the GTR on light vehicle emissions into UN type approval regulations, including handling of current UN Regulations on emissions (notably, UN R83 and UN R101) and process for implementing the WLTP requirements.

Pursuant to GRPE discussions, the proposal adds the following paragraph to the amendment:
“At the manufacturer’s request, type approval granted under this Regulation may be extended from vehicles mentioned above to special purpose vehicles of categories M1, M2, N1 and N2 regardless of their reference mass. The manufacturer shall demonstrate to the Type Approval Authority which granted the type approval that the vehicle in question is a special purpose vehicle.”

WLTP informal working group refinements to the amendment proposal.

Complete version of GTR No. 15 including the proposed Amendment 2 (GRPE/2017/7) and latest refinements by the WLTP informal group (GRPE-74-02). Amendment 2 corresponds to phase 2a development of the GTR, including the following modification to the text:

1. If an alternative value is applied for a parameter, such as a higher n_min_drive or an ASM, this parameter value has to be the same within an interpolation family (Paragraph 5.6.1.).
2. The mass in running order used for the calculation of the power to mass ratio is replaced by mass in running order minus 75 kg (paragraph 1. of Annex 1).
3. Idle engine speed n_idle is removed from the power curve measurement requirement (paragraph 2. of Annex 2).
4. The additional safety margin (ASM) value may be decided by manufacturer rather than the prescribed exponential curve (paragraph 3.4. of Annex 4).
5. The number of decimal place of road load coefficients is defined (paragraph 2.4. of Annex 4).
6. Additional restrictions are set to the application of the split run method for coastdown testing (paragraph 4.3.1.3.4. of Annex 4).
7. Specific data rejection criteria are added (paragraph 4.3.1.4.3. of Annex 4).
8. The “delta method” for road load determination is added (paragraph 6.8. of Annex 4 and other paragraphs. See section 4.4.25.for more detail).
9. The roller radius correction factor is modified(paragraph 6.6.3. of Annex 4).
10. The allowable combination of the test vehicle selection and family requirements are further clarified (paragraph 4.2.1.3. of Annex 4 and other paragraphs of Annex 4).
11. Provisions for an additional cooling fan are included(paragraph 1.1.5. and 1.1.6. of Annex 5).
12. The correction of measurement/recording frequency requirements are specified (over several annexes).
13. Calculation of the n/v ratio is defined (paragraph 8. of Annex 7).
14. The stepwise procedure for calculating the final test results of OVC-HEVs is added (paragraph 4.6. of Annex 8).

Proposal to restrict the application of CO2 specific emission limits only to NMHC and CO emissions (back-to-back comparison of NOx and PM to apply under the regulation in any case). The proposal also aligns the text where applicable with the intent of paragraph 2.3.15.: “R49 original emission limits” means the emission limits as defined in Regulation No. 49 to which the original engine system was approved."

Proposal to add the following paragraph to the draft amendment presented in document WP.29/2016/87:

9. Entry into force

The provisions set in Revision 2 to Rule No. 1 on uniform provisions for Periodical Technical Inspections of wheeled vehicles with regard to the protection of the environment shall enter into force on 1 June 2018.

Report on the status of the International Whole Vehicle Type Approval program with regard to regulations under the purview of GRPE.

Japan’s proposal for EPPR-17-08 (EPPR-11-15e Rev.3) B.2.

Proposal to align the entry into force of the draft Revision 2 to Rule No. 1 and Revision 1 to Rule No. 2 with the application date of the corresponding requirements set in the roadworthiness directives of the European Union to facilitate application by Contracting Parties to the 1997 Agreement that are also member-states of the European Union.

Positions of participants and consensus within the EPPR informal group on amendments to GTR No. 2.

This proposal has been prepared by the EPPR IWG Secretary, in close collaboration with WLTP IWG experts, in order to align the definitions of chassis dynamometer rollers between EPPR and WLTP GTRs. The content of this overview has been followed by WLTP although the specific definitions are not contained in GTR No. 15. This proposal recommends elaborating and introducing such definitions into the EPPR GTRs.