Proposal from China to modify the photometric performance requirements of front position lamps integrated with front fog lamps and of rear position lamps integrated with rear fog lamps (analogous to the treatment of position lamps integrated into headlamps).

Proposal to ensure that the signal requirements to indicate the activation of a failure tell-tale are not constrained to a particular type of light source. The current wording of UN R6 relates only to filament lamps; other light sources should be treated identically to avoid design restriction.

Proposal to align the cut-off requirements of UN R19 with UN R98 and R112 such that the cut-off quality (sharpness (G value) and linearity of the cut-off) are only assessed when the vertical adjustment cannot be performed repeatedly to the required position due to an unclear cut-off.

Proposal to amend the title of UN R31 by inserting “Halogen” and using the abbreviation “HSB” in order to distiguish the regulation from UN R5. In its justification, GTB also raises the “freezing” of both these regulations as they relate to outdated technologies for future consideration.

Proposal from the Working Party “Brussels 1952” (GTB) to introduce a new category of amber dual-filament light sources PY21/5W into UN R37.

Proposal from the Working Party “Brussels 1952” (GTB) to clarify color measurement requirements.

Proposal from the Working Party “Brussels 1952” (GTB) to update provisions on heat resistance tests.

Proposal from the Working Party “Brussels 1952” (GTB) to amend the requirements on light-source failures (paragraph 7.4. (“n-1 rule”)) in order to permit the introduction of new cost-efficient designs for daytime running lamps.

Proposal from the Working Party “Brussels 1952” (GTB) to revise paragraph 5.23 to clarify the requirements on the replacement of light sources approved according to UN R37.

Proposal from the Working Party “Brussels 1952” (GTB) to delete the 1 candela requirement for geometric visibility.

Proposal from the Working Party “Brussels 1952” (GTB) to amend the geometric visibility provisions.

Proposal from the Working Party “Brussels 1952” (GTB) to amend the provisions concerning the requirements for geometric visibility of devices for adaptive rear lighting.

Proposal from the Working Party “Brussels 1952” (GTB) introducing a new category LW2 into the new draft Regulation for LED light sources ¹²⁷ and introducing some editorial amendments to the existing text.

Proposal from the Working Party “Brussels 1952” (GTB) to introduce interdependent lamps (“Y” Lamps) into the Regulation.

Proposal from the International Organization of Vehicle Manufacturers (OICA) to extend the scope of UN R10 to all kinds of power train systems above a certain working voltage level when they are in charging mode and enable the type approval of separate electrical components (ESA).

Proposal from the Working Party “Brussels 1952” (GTB) to delete the 1 candela requirement for geometric visibility. In the original document, the strikethrough proposed for the contents of paragraph 6.2.5 was omitted. This document corrects that omission.

GTB proposal to amend the geometric visibility provisions. Subsequent to the preparation of the proposed amendments in document GRE/2012/42, several editorial corrections have been identified by GTB experts. This document replaces that original submission.

Proposal from Germany to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

Proposal from Germany, prepared with support from the Netherlands, to insert provisions for the use of light source control gear in the case of halogen incandescent light sources.

Update by the IEC of the German proposal for revisions to IEC 60809 and 60810 in accordance with UN Regulations for signalling devices to address risks in the use of low-quality non-replaceable filament lamps.

Correction to the proposal from Working Party “Brussels 1952” (GTB) to revise paragraph 5.23 to clarify the requirements on the replacement of light sources approved according to UN R37.

Update by the IEC of the German proposal for revisions to align IEC 60809 and 60810 with UN Regulations for signalling devices to address risks in the use of low-quality non-replaceable filament lamps.

Submission from the International Electrotechnical Commission (IEC) to correct the omission of the letter “q” from the cap designation of category PR27/7W in Regulation No. 37.

This is a generic proposal to require approval according to a light source
regulation prior to an application for approval under UN R10. It appears that LED retrofit light sources are offered to the market with Regulation No. 10 approval only where they should also be subject to the new UN R127.

During the 64th GRE session, GTB was charged to review and update the transitional provisions of Regulation 48. This draft proposal has been developed by the GTB Installation Working Group in close cooperation with OICA.