Proposal to delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

In document GRE/2014/9, IMMA proposed the use of different brake lamp activation methods and the introduction of high-mounted stop lamps to improve the conspicuity of “powered two-wheelers” under Regulation No. 53. In this document, India offers a number of editorial recommendations.

In document GRE/2014/7, IMMA proposed to introduce the possibility of interdependent lamps for dedicated motorcycle lamps as Supplement 17 to Regulation No. 50. The concern was that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features. In this document, India proposes to clarify that the installation height of the device must be less than or equal to 750 mm.

Brief presentation raising question over the necessity to have triangular reflectors on the rear of large trailers and seeking greater flexibility in such rear reflectors.

Report of the Working Party on Lighting and Light-signalling Equipment on its April 2014 session.

Draft agenda for the October 2014 GRE session without annotations (descriptions of agenda items and document references).

Revised proposal (superseding document GRE/2014/7) to introduce the possibility of interdependent lamps for dedicated motorcycle lamps. The proposal reflects recent amendments to Regulations Nos. 6 and 7 and meets the visibility angle requirements of Regulations Nos. 50 and 53. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Revised proposal (superseding document GRE/2014/8) to allow for the installation of interdependent lamps for L3 category vehicles. The amendment also reflects recent amendments to Regulation No. 48, Supplement 2 to its 06 series of amendments and further includes some editorial corrections of current Regulation No. 53 texts. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Proposal to amend UN R3 in order to address the recent introduction of devices with a reduced light distribution to be mounted no higher than 750 mm. 1. The proposal would also require colorimetric and photometric testing to type approve each variation in color of an approved device.

Proposal to delete unnecessary markings for LED front fog lamps that have non-replaceable LED modules and to correct and clarify the requirements for colour measurement and ultraviolet (UV) testing of light emitting diode (LED) modules.

Proposal to amend the test procedure for reversing lamps and maneuvering lamps equipped with light sources other than filament lamps. Currently, the lamps are required to meet photometric parameters after one minute and 30 minutes of operation. Under normal use, these lamps are operated for no more than six minutes at a time. This proposal would set the second measurement point at 10 minutes rather than 30 minutes. This change would also align the procedure with SAE standard J1889.1.

Proposal to introduce new halogen categories H18, H19 and H20 and some minor corrections to existing categories.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Front fog lamps may be reciprocally incorporated with the main beam and in some cases, it is required to switch off the front fog lamp when the main beam is operated to avoid overheating of the device. In this case, Regulation No. 19 requires a “/” in the approval marking. However, the current text in paragraph 6.3.7 of Regulation No. 48 requires that “it shall be possible to switch the front fog lamps ON and OFF independently of the main-beam headlamps”. This proposal is intended to remove the conflict between the texts of the two regulations.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal to introduce a new category: D8R.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s) and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Consolidated proposal prepared by AVLI informal working group to update and revise Regulation No. 86.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity. The proposal would also simplify the measurement of the objective luminous flux of light emitting diode (LED) module(s) and correct the ultraviolet (UV) table in the regulation.

Proposal to introduce new categories LR3A, LR3B, LR4A, LR4B and correct one value in the ultraviolet (UV) table.