Consolidated version of UN R106 including ETRTO proposed amendments (see documents GRRF/2018/6 and GRRF/2018/7).

This document consolidates previous documents GRRF/2017/19 and informal document GRRF-84-17 taking into account the request for addition of tyre sizes and tyre classification codes common in the United States and standardised by the Tire and Rim Association, but needed to be added to UN Regulation No. 106 in order to permit their type approval in order to conform to Regulation EU 167/2013 for tyres to be exported to Europe. It includes addition/modifications of some paragraphs to the main text of the Regulation as well as the addition of some tyre size designations to Annex 5 and Annex 7:

1. ISO 4251-4 replaced by ISO 18805
2. Paragraph 2.33.2 deleted since new tables for IF and VF were added to Annex 7
3. Paras 3.2., 3.2.2. and 5.4. modified because “tyres submitted for approval” cannot bear an approval mark until approved and the “only” as it is written can be misunderstood. Para. 3.2.2. was aligned to the wording in other UN Regulations. Reference to para. 3.3 in paragraph 5.4. is deleted because paragraph 3.3 does not refer to specific markings
4. Para 6.1.2. amended to align the wording to the headers in Annex 5 and to correct the reference to the footnote
5. Para 6.2.1. amended to restore the proper references after renumbering resulting from the latest Supplements
6. The amendment of Annex 5, Table 5 adds the value for the overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”
7. Annex 5, Table 6, Note 1 amended because most of the tyre sizes listed in the table, especially those identified by the “classification code I‐3” (i.e. Traction tread), are currently available in both versions: ‘implement’ to be used on agricultural machinery and ‘IND’ to be used on construction vehicles. The two types of tyres have the same type of size designation and the same dimensions. Therefore some manufacturers identify those tyres with the suffix ‘IND’ rather than with the suffix ‘IMP’ thus applying the variation of load capacity with speed as published in Annex 7 Part E. The reason for this proposal is to avoid a duplication of tables with a new table only replacing the suffix IMP with the suffix IND.
8. The addition of the footnote to Annex 5, Table 7 answers the request by GRRF to introduce appropriate formulae in the Regulation instead of continuously updating Annex 5.
9. References in Annex 7 corrected pursuant to the renumbering following the introduction of three new paragraphs in Supplement 15 approved during the 172nd session of WP.29.
10. Annex 7, Part A amended to conform with Tire and Rim Association specifications for code designated diagonal tyres with speed symbol A8.

Proposal to add markings for the inflation pressure to be used for measurements and tests.

Proposal for new tables covering shallow-tread drive wheel tyres for agricultural tractors – normal section sizes and for additional specifications for high flotation tyre dimensions.

Proposal to

1. amend para 6.1.2. to align the wording to the headers in Annex 5 and to correct the reference to the footnote
2. amend para 6.2.1. to restore corrent references after renumbering made during recent Supplements
3. amend Annex 5, Table 5 to add the value for the Overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”.
4. amend Annex 5, Table 6, Note 1 to clarify use of the ‘IMP’ and ‘IND’ suffixes for agricultural implements and construction vehicles, respectively.
5. add a footnote to Annex 5, Table 7 is the to introduce the appropriate formulae in the Regulation (instead of via Annex 5)
6. correct cross-references in Annex 7 following the introduction of three new paragraphs in Supplement 15
7. amend Annex 7, Part A to conform with Tire and Rim Association (TRA) specifications for code designated diagonal tyres with speed symbol A8.

Proposal to introduce new tyres size usually listed in Annex 5 in a new Resolution in order to simply maintenance of this annex and reduce the volume of amendments. This proposal includes changes regarding Improved Flexion (IF) tyres and Very high Flexion (VF) tyres. The proposal harmonizes with EU framework legislation for agricultural vehicles.

Amendment, per GRRF discussions, to remove the proposal to require the use of kPa markings and the related transitional provisions from the broader set of amendments to UN R106 proposed in document GRRF/2017/9.

Proposal to add tyre and rim dimensions and to add a diameter code ‘d’ of 28.5 (Please note that the “28.5.5” shown in the table is a typo and should be “28.5”).

Proposal to amend the transitional provisions of the formal proposal to update UN R106 (GRRF/2017/9).

Revised proposal for a “Mutual Resolution on dimensions of tyres of certain size designations”.

Revised version of the proposal to include UN R106 tyre dimensions in a Mutual Resolution on tyre sizes. The amendment to the table listing the allowed nominal rim diameters (d) is needed to allow the approval of standardized sizes which exist and are already on the waiting list for type approval.

Germany reviews problems with applying UN specifications for the marking of winter tyres, covering disparities in definitions and performance requirements across the tyre regulations (UN R30, R54, R75, R106, R108, R109 and R117). Therefore, Germany proposes that GRRF work to resolve these disparities and offers two possible solutions: 1) Introduce the definition of "Snow tyre for use in severe snow conditions” and the related performance and marking requirements established under UN R109 and R117 into UN R30, R54, R75, R108, and (possibly) R106; 2) Amending UN R117 to extend the scope of its snow performance criteria to additional tyre classes and categories, such as special tyres (POR, MPT), all terrain (AT) tyres, and retreaded tyres for passenger cars.