Proposal to avoid placing requirements in the Definitions section and to facilitate the text by making use of the definition of “service description” that was introduced by Supplement 24.

ETRTO detected an issue in document ECE/TRANS/WP.29/2022/7 with the insertion of paragraph 3.5.1. that is the consequence of the alignment between UN Regulation No. 54 and UN Regulation No. 109. This new requirement regarding the marking position in the sidewall for retreaded tyres is creating a burden for the retread industry that will potentially need to adapt all their moulds accordingly, without considering transitional provisions.

Proposal to introduce provisions to allow type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for tyres complying with these requirements.

Proposal to introduce provisions to allow the type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for those tyres complying with these requirements.

Proposal to correct editorial mistakes in document GRBP/2021/17 that were not corrected by informal document GRBP74-31-Rev.1.

Proposal to introduce a new definition of traction elements to characterize traction tyres.

Proposal to address the definition of the radial structure (as a continuation to ECE/TRANS/WP.29/GRBP/2021/9), the definition of snow tyres, the requirements for special use tyres of class C1, the addition of an optional prefix for extra load tyres, a clarification of the description of the load/speed test for run flat tyres and extended mobility tyres (EMT) and editorial corrections.

Proposals for editorial corrections to the provisions for type approval of special use tyres that fulfil the requirements for snow performance

Proposal for editorial corrections

Proposal introduces provisions to allow the type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for those tyres complying with these requirements.

Updates the reference to latest version of ISO 10844:2021

Re-introduces the definition of traction tyre as this can be still used between the entry into force date of the 04 series of amendments and 7 July 2024 .

Proposal introduces provisions to allow the type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for those tyres complying with these requirements

Editorial corrections and amends the transitional provisions

Proposes the amendment to the transitional provisions aligning with other proposals

Proposal to address the following:

1. “Special use” tyres with nominal rim diameters larger than those listed in the present table (rim diameters up to 42, section widths up to 750 mm and overall diameters over 2 meters) and with speed symbols F and above have been announced in the European market as original equipment of N3G “special purpose vehicles” (i.e., special high speed self-propelled vehicles for agricultural and forestry use, like wood choppers).

2. Existing multi-purpose tyres (MPT) (classified as “special use tyres” as per paragraphs 2.5.3. and 3.1.13.), already type approved since years, have a tread pattern with lugs or cleats in addition to those with blocks, as evidenced by the attached slide showing some examples. It is proposed to amend paragraph 6.3.1. by clarifying that lugs and cleats are possible shapes of the mentioned blocks.

3. Testing tyres with very large overall diameters, sometimes over 2 m, on a test drum with a diameter of 1.70 m ± 1 % would be unpracticable. For practical reasons most of those
tyres are regularly tested on drums with a diameter of 3 m or even larger. The proposal carries equivalence provisions from UN R106 to justify the equivalence of the test method as required by Annex 7 in point 4 “Equivalent test methods" and clarifies based on UN R117 the formula already used indirectly.

4. Some commercial vehicles are often used in the market at a reduced speed of 70 km/h with a load-capacity of the tyres increased as per load/speed combination defined in the table of Annex 8. The proposal would allow use of the speed category symbol E (but restrict it to “additional service description”) to provide this information.

5. Considering that 32 km/h is already a floor value for the test-drum speed for diagonal tyres, ETRTO proposes not to apply to E speed category symbol tyres the linear decrease of
the test-drum speed in function of the decrease of the speed category symbol by keeping, for safety reasons, the same test-drum speed as for F speed category symbol tyres, i.e., 32 km/h).

6. In the case of additional service descriptions mentioned in paragraph 6.2.5.1., it is proposed not to perform the additional load/speed test because the load-capacity approximates with a negligeable difference the reduction or the increase in percentage of the nominal load/speed combination applicable to the nominal speed category symbol (see Annex 8).

7. Type approval applications for radial tyres with load capacity index greater or equal to 122 and without the additional marking “LT”, or “C” have been done in the past for the speed category symbol N for which the load/speed endurance test procedure is not described in Annex 7, Appendix 1. To type approve such tyres the test speed was separately defined by the different involved Type Approval Authorities. In order to harmonize the test procedure to be used for the type approval of such tyres, it is proposed to amend the Annex 7, Appendix 1 by introducing testing conditions in line with the rule applied for defining the test speed of radial tyres with load capacity index greater or equal to 122 (i.e. starting from 32 km/h set for F speed category symbol, the test speed is increased by 8 km/h respect to the one set for the previous speed category symbol).

8. The definition of “snow tyre” is amended to clarify that “snow tyres” are not only suitable for the use in snow conditions but also on mud and by replacing the term “maintain vehicle motion” (i.e. keeping the vehicle speed and direction of movement constant) by a more general concept of “controlling vehicle motion” (i.e. also being able to change the vehicle speed and direction of movement as intended).

9. It is proposed to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by caliper” which fix a technical limitation. The removal of this technical limitation would be advisable following the principle of not stopping the technical innovations.

10. Editorial corrections are introduced to ensure that the terms “load-capacity” and “speed category symbol” are used consistently throughout the text and to remove some typing mistakes present in the current text.

Proposal to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by calliper”, add the definition of “special tyre”, clarify the definition of “snow tyre”, to enable the case of a “special tyre” fulfilling the definition of a “snow” tyre, clarify application of the suffix “M/C”, and make editorial corrections and clarifications.

Proposal to delete obsolete footnotes concerning worn tyre wet grip and approvals under UN R117 coincident with approvals under UN R54. The 04 series of amendments to UN R117 introduces the requirements on adhesion of tyres in worn state on wet surfaces for tyres within the scope of UN R54.

Proposal to extend the scope of the speed category E to align with the technical evolution of agricultural and forestry vehicles.

The prescription given in paragraph 3.5.2., which will be implemented through document WP.29/2022/7/Rev.1 adopted by WP.29, contradicts the previously existing prescription in paragraph 3.2.9. This proposal aims to resolve the contradiction by amending paragraph 3.5.2. to introduce a reference to the prescriptions given in paragraph 3.2.9.