Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to establish a requirement for easy access to the LPG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.

Proposal to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories. The proposal aims to ensure proper coordination between container approvals (which involve testing with accessories attached) and accessory approvals (which may be subsequent to the original container approval and therefore, relevant to its validity).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

Proposal to allow for the approval of systems using non-seamless double and single wall tubes subject to testing for high pressure and high resistance to pressure pulses. The proposal would also add general test requirements for LPG fuel lines and couplings based on ISO Standard 15500 for compressed natural gas equipment.

In GRSG/2017/10, Poland proposes requirements for the LPG tank and its accessories. AEGPL notes that UN R67 requires a specific bonfire test of the container equipped with specific configurations of accessories which includes markings to indicate the extension number of each accessory corresponding to each configuration. In order to ensure that the user knows whether an accessory can be fitted with a specific container, AEGPL proposes to require marking the extension number on the accessories relevant to the bonfire test (multivalve, pressure relief valve and pressure relief device) in order to prevent/forbid the fitting of any accessory not approved for use in each container configuration. This alternative proposal to that in GRSG/2017/10 would imply a new marking requirement for accessories, but would avoid the proliferation of accessory type-approval numbers and increase in paperwork.

Proposal to introduce tolerances for dish, bayonet, and acme filling units in order to reduce risks of misuse in connecting these filling units with nozzles.

Proposal to introduce a maximum service life requirement of 15 years and for the location of the filling unit of the LPG tank on vehicles.

Proposal to require that components connecting the pressure relief device with the gaseous phase be made of metal.

Presentation supporting GRSG/2017/10 to clarify the definitions of LPG container accessories to facilitate coordination between the separate, independent approvals required for the LPG container and for its accessories.

Proposal to establish procedures for the approval of non-seamless double and single wall gas tubes provided they can withstand the applicable tests according to Annex 15.