Corrections to proposals WP.29/2026/63, WP.29/2026/65, and WP.29/2026/71.

Proposal to amend UN R17 Supplement 1 to the 12 series of amendments. The Regulation is amended to account for vehicles of category X. Vehicles of category Y are not in the scope of this Regulation. The Regulation is extended to vehicles without driver and manual driving controls. Multiple amendments are made to definitions, test procedures, and technical requirements for seats, anchorages, and head restraints, including changes to measurement planes, test parameters, and displacement specifications across various annexes and paragraphs.

Proposal to account for vehicles of categories X and Y, extend application to vehicles without driver and without manual driving controls, and address inconsistencies related to REESS provisions. The amendment introduces ADS feature types 1 and 2, modifies warning transmission requirements for ADSF-2, adjusts isolation resistance specifications, and exempts certain REESS requirements for category O and Y vehicles. Changes include updates to Annex 8 stopping conditions and Annex 9E terminology.

Proposal to extend application of UN R127 to vehicles of category X and those without drivers or manual driving controls, modify scope provisions, update headform acceleration criteria in paragraph 2.48, add new approval mark provisions distinguishing WAD 2,100 versus WAD 2,500 boundaries, require mandatory notification and uploading of test results to the DETA database, and set transitional provisions with dates through 2033 for type approvals and acceptance of previous amendments.

Proposal to extend UN R134 to vehicles of category X (excluding vehicles of category Y), add provisions for Periodic Technical Inspections, modify hydrogen concentration warning requirements for ADS features of type 2 to transmit logic signals to the ADS, and adjust test cycle specifications in Annex 3.

Proposal to extend the scope to vehicles of category X (application to vehicles without driver and manual driving controls), to define door closure warning systems, address ADS features of type 1 and type 2, add requirements for door locking devices on vehicles equipped with ADSF-2, and modify references to driver-side impacts by impacts on one side of the vehicle.

Proposal to extend the scope to include vehicles of category X, replace “driver” by “occupant”, and separate the scope into vehicles with regard to protection of occupants against the steering mechanism and electrical shock in a frontal collision and steering controls with regard to protection of occupants in the event of impact.

Proposal to enable application to vehicles of category X. For vehicles equipped with an Automated Driving System other than vehicles of category X, in manual driving mode no special provisions apply. In a mode where an ADS feature is active, the relevant requirements for ADS vehicles apply.

Proposal to enable application to vehicles of category X (vehicles of category Y are not in scope). For vehicles of category X, the R point of the most forward passenger seat shall be taken instead of the R-point of the driver’s seat. Amendments address steering control contact requirements and modify occupant references.

Proposal to enable application to vehicles of category X, including prohibition of one-touch closing when an ADSF-2 is active, requirement for auto-reversing devices for power operated windows that can be operated by an ADSF-2, and user manual instructions for power-operated systems including warnings regarding improper use and driver and ADS responsibilities.

Proposal to enable application to vehicles of category X (vehicles of category Y are not in scope) with amendments addressing steering wheel hub provisions, cab positioning, and seating requirements for vehicles of category X. Cabs for vehicles of category X mounted in other positions than vehicle front shall not be taken into account for frontal collision simulation.

Proposal to enable application to vehicles of category X, including attention to ADAS/ADS sensors and providing specifications for test procedures and dummy positioning requirements for vehicles of category X in frontal collision protection testing.

Proposal to enable application to vehicles of category X with a gross vehicle mass of up to 3,500 kg. The most forward passenger seat R-point shall be taken instead of the driver’s seat R-point for vehicles of category X. Amendments clarify provisions related to sensors, testing procedures, and applicability to vehicles without drivers.

Proposal to enable application to vehicles of category X. Amendments specify dummy placement and positioning requirements for vehicles of category X, including provisions for both right and left hand traffic configurations. Vehicles of category Y are excluded from the scope.

Proposal to enable application to vehicles of category X (vehicles of category Y are excluded from the scope). For vehicles of category X, the R point of the most forward passenger seat shall be taken instead of the R-point of the driver’s seat. The proposal amends the provision on “anti-rotation device” to read, “An anti-rotation device for an ISOFIX semi-universal child restraint system consists of either a top tether, the vehicle dashboard, a support leg or any other means intended to limit the rotation of the restraint during a frontal impact”.

Proposal to enable application to vehicles of category X. In the absence of a driver or manual driving controls, provisions related to them shall not be taken into account if not already covered by this amendment. Vehicles of category Y are not in the scope of this Regulation. In manual driving mode, no special provisions or exemptions apply to vehicles equipped with an Automated Driving System other than vehicles of category X.

Proposal to enable application to vehicles of category X. For vehicles of category X, the R point of the most forward passenger seat shall be taken instead of the R-point of the driver’s seat. A seating position with steering control placed in front may be designated as suitable for Child Restraint System installation if requirements for a passenger seating position are fulfilled. The Regulation does not apply to vehicles of category Y.

Proposal to clarify exemptions for folding seats, delete a condition on neutral transmission position for first-level warnings, harmonize the “vehicle master control switch” definition with UN R159, ensure drivers receive initial warnings when entering vehicles with remotely activated switches, ensure clear voice communication during emergency calls, and enable application of UN R174 to vehicles of category X, including requirements for safety-belt reminders in first-row seats of category X vehicles and permission for ADS management of safety-belt reminders if equivalent safety is provided.

Proposal to introduce references to ADS acceleration demands, establish speed limitation requirements for vehicles of Categories X and Y, require ASLF and ASLD deactivation upon ADS feature activation, and specify testing procedures including dedicated activation methods for vehicles without manual driving controls.

Proposal to amend paragraph 1.1.1. to insert a new footnote 7 defining replacement brake lining assemblies; amend footnote 4 referencing the Consolidated Resolution on the Construction of Vehicles; and amend Annexes 3, 4, 7, 11, and 14 to establish special provisions for vehicles equipped with an Automated Driving System, including dedicated activation methods for braking tests, demonstration requirements for test activation method accuracy, recording of braking demand in test reports, and speed limitations at 90 per cent of v_max for vehicles of categories X and Y.

Proposal to clarify that the Regulation does not apply to vehicles of categories X and Y, add an alternative approval pathway for certain vehicles using UN R152 requirements, allow continued extension of approvals for 12 months, amend paragraph 10 of Annex 1, and revise Annex 2 (approval mark arrangements).

Proposal to insert new paragraph 1.2.3 relating to vehicles of categories X and Y, amend footnotes 1 and 3 to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev.8, and insert new paragraph 5.7 stating that while an ADS feature is active, the BAS shall not influence the performance of the braking system.

Proposal to delete footnote in paragraph 1; add bicycle impact avoidance to scope; amend paragraphs 2.13 and 2.14 regarding road adhesion definitions and Peak Braking Coefficient measurements; amend paragraph 5.4.2.3 requiring two deliberate actions for AEBS deactivation via ESC; renumber footnotes 2 through 9; and insert new paragraphs 5.4.4.1 to 5.4.4.3 to establish special provisions for vehicles equipped with an ADS.

Proposal to insert a new paragraph 1.2. stating that this Regulation does not apply to vehicles equipped with an ALKS that has been approved as an ADS feature in accordance with the UN Regulation on the approval of vehicles equipped with an Automated Driving System (i.e., where the ALKS has already been approved under the ADS regulation).

Proposal to introduce new definitions for Automated Driving System (ADS), Dynamic Driving Task, bidirectional vehicles, Enhanced Exterior Sound (EES), and Vehicle Master Control Switch; amend specifications for test mass, sound levels, and measurement procedures for vehicles of categories M₁–M₃, N₁–N₃, and vehicles equipped with an ADS; add provisions for vehicles electrically propelled without internal combustion engines; establish ASEP control ranges and calculation methods; and insert Annex 10 with specific provisions for testing vehicles equipped with an ADS.

The proposal adds Annex 5 on special provisions for testing vehicles equipped with an Automated Driving System (ADS) and adds definitions for ADS, Dynamic Driving Task, Category X and Y vehicles, logical signal, and Vehicle Master Control Switch. Amendments modify run-flat warning system requirements, braking performance tests, and tyre detection procedures to accommodate ADS-equipped vehicles.

Proposal to add Annex 5 Special provisions for the testing of vehicles equipped with an Automated Driving System (ADS) to UN R138. The proposal amends paragraphs 2.7 and 2.8, inserts new paragraphs 2.13 to 2.16 defining ADS, Dynamic Driving Task, bi-directional vehicles, and forward direction, renumbers former paragraph 2.13 to 2.17, amends paragraph 6.2.5 regarding available AVAS sounds, amends Annex 1 item 1.2.2, amends Annex 3 paragraph 3.3.1 regarding testing conditions for bi-directional vehicles, and adds the new Annex 5 explaining how to adapt UN R138 to vehicles equipped with an ADS.

Proposal to amend UN R141 under section 2 to add definitions of Automated Driving System, Dynamic Driving Task, Category X vehicles, Category Y vehicles, Logical signal, and Vehicle Master Control Switch, amend under section 5 to update performance requirements and warning signal specifications for vehicles equipped with an ADS and towed vehicles, amend Annex 1 to add a vehicle ADS status field, amend Annex 3 regarding test procedures for TPMS including deactivation of TPRS and CTIS, amend Annex 4 regarding test weight and refill functionality checks, amend Annexes 5A and 6 regarding towed vehicle communication interfaces, and insert new Annex 9 containing special testing provisions for vehicles equipped with an ADS.

Proposal to amend paragraph 1, footnote 1, insert new paragraphs 2.23. to 2.26. defining Automated Driving System, Dynamic Driving Task, Category X vehicles, and Category Y vehicles, amend paragraph 4.4.1., footnote 2, amend section 5.2.3. to add requirements for vehicles equipped with an ADS and exclude speed warning label requirements for vehicles of categories X and Y, amend Annex 1, footnote 4, insert new item 6.2. regarding ADS equipment, insert new paragraph 2.2. in Annex 2 Section I regarding ADS equipment, and insert new paragraph 4.2. in the Addendum to communication form regarding brief description of the ADS if fitted.

Proposal to add a new Table of contents section 7 for special provisions testing vehicles equipped with an ADS; amend footnotes in paragraphs 1.1. and 2.2.; amend paragraph 6.1.3. on available sounds; insert new paragraphs 11.4. through 11.8. define Automated Driving System, Dynamic Driving Task, and Category X and Y vehicles; amend paragraph 14.1.5. on available sounds; amend paragraph 14.3. on pause function for manual and ADS operation; insert new item 0.13. in Annex 1B, Appendix 1 regarding ADS equipment; and insert new Annex 7 with special provisions for testing vehicles equipped with an ADS.

Proposal to insert new paragraphs 0. and 0.1. to 0.1.2., and amend footnotes 1 and 2 in UN R18. Supplement 5 to the 03 series of amendments is introduced to take into account vehicles of categories X and Y, as well as vehicles with a manual mode operating at speeds above 6 km/h which are equipped with an Automated Driving System. The amendment extends application to vehicles without driver and without manual driving controls. In case of vehicles equipped with an ADS, in any driving mode no special provisions or exemptions apply. Footnotes are amended to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3).

Proposal to insert new introductory paragraphs addressing vehicles of category X and vehicles with manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, amend footnote 1 to paragraph 1.1. to reference ECE/TRANS/WP.29/78/Rev.8, amend footnote 2 to paragraph 4.1.4.1. to reference ECE/TRANS/WP.29/78/Rev.8, and amend paragraph 6.17.4.2. to establish an exception for aerials located behind the vertical transversal plane passing through the “R” point of the driver with a maximum projection not exceeding 70 mm, or for vehicles of category X, behind the vertical transversal plane passing through the “R” point of the foremost occupant.

Proposal to insert new paragraphs 0. and 0.1. to 0.1.2. addressing vehicles of categories X and Y and vehicles with manual mode operating at speeds above 6 km/h equipped with an ADS, amend paragraph 1., footnote 1 to reference ECE/TRANS/WP.29/78/Rev.8, amend paragraph 3., footnote 2 to reference ECE/TRANS/WP.29/78/Rev.8, Annex 3, amend para. 4.3. to define “Occupant compartment”, and amend paras. 5.5. to 5.8. to specify tank placement, partition requirements, fuel leakage prevention, and filler hole location.

Proposal to insert new paragraphs 0., 0.1., and 0.1.1. introducing Supplement 2 to address vehicles of categories X and Y and to exclude vehicles without manual driving controls, amend para. 1 Scope to apply to vehicles of category M₁ equipped with foot controls, amend footnote 1 to para. 1 and footnote 2 to para. 4.4.1. to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3).

Proposal to insert new paragraphs 0. and 0.1. to 0.1.4., amend paragraphs 2.6., 2.7., 4.4.1., 5.1., 5.2., and 5.5. to 5.11., insert new paragraphs 2.9. and 2.10., and amend paragraph 1., footnote 1, to extend UN R39 application to vehicles of categories X and Y and vehicles with manual mode operating at speeds above 6 km/h equipped with Automated Driving System Feature of Type 2 (ADSF-2), revise speedometer and odometer requirements accordingly, and clarify provisions related to driver absence and manual driving controls.

Proposal to insert new paras. 0. and 0.1. to 0.1.4. introducing vehicles of categories X and Y and vehicles with manual modes or automated driving systems, amend para. 1(a) footnote 1, para. 2.13., para. 2.25., paras. 5.4.1. and 5.11.1. footnote 2, insert new para. 2.40. defining “Safety Concept”, amend para. 6.2., para. 7., para. 8.2.1.1., Annex 1A para. 5.1., Annex 3 footnote 18, Annex 21 title, Annex 22 title, and Annex 24 including its scope, definitions, and provisions for safety glazing installation on vehicles. This proposal is based on GRSG-131-23-Rev.1.

Proposal to account for vehicles of categories X and Y and vehicles with manual mode operating above 6 km/h equipped with an Automated Driving System, clarify scope exclusions, define “Safety Concept,” update references to the Consolidated Resolution on the Construction of Vehicles, establish that indirect vision requirements do not apply during active ADS features, and permit alternative requirements for category X vehicles with on-board manual operation not using a driver’s seat.

Proposal to enable application of UN R55 to vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, insert footnote 1 defining these vehicle categories, amend Annex 5 paragraph 7.4. to require that release of fifth wheel coupling locking devices require intentional action by the driver or operator or by ADS and that engagement status be transmitted as a logic signal to ADS, amend paragraph 10.4. to require that engagement status be transmitted as a logic signal to ADS, amend paragraph 13.2. to reference remote indication for the driver or operator, amend paragraph 13.2.8. to provide for automatic reactivation when the coupling is next opened and closed, amend paragraph 13.3.3. to clarify indication to the driver or operator of conditions under which external force acts on the coupling, and insert new paragraph 13.4. requiring transmission of a logic signal to ADS indicating at least the closed and doubly locked position of the coupling.

Proposal to insert new paragraphs 0., 0.1. to 0.1.3. to introduce Supplement 4 to the 03 series of amendments to account for vehicles of categories X and Y and vehicles with manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, amend footnote 1 to paragraph 1. to reference the Consolidated Resolution on the Construction of Vehicles document ECE/TRANS/WP.29/78/Rev. 8, amend footnote 2 to paragraphs 6.4.1., 15.4.1., and 24.4.1. to reference Annex 3 to the same document, and amend paragraph 16.7. to specify label placement for adjustable Rear Underrun Protective Devices at the driver’s place or rear area next to the device.

Proposal to insert new introductory paragraphs 0. and 0.1. to 0.1.3., amend paragraph 1.1. footnote 1, amend paragraph 2.5., and amend paragraph 4.4.1. footnote 3 to UN R61. The supplement extends application to vehicles of categories X and Y without driver, driver cab, or manual driving controls, and vehicles with manual mode operating above 6 km/h equipped with an Automated Driving System. Provisions related to driver, driver cab, or manual driving controls shall not apply if not covered by the amendment. For vehicles of category Y without a cab, the cab rear panel shall be replaced by a theoretical vertical transversal plane located 350 mm behind the rearmost point of the tyre of the foremost front axle.

Proposal to insert new paras. 0, 0.1 to 0.1.3, amend paras. 1, 5, 6, 6.17.2.1, 16, 17, 17.1.7.1, 17.8.8, 17.8.8.1, 17.10.2, 17.11.4, and 17.13.2.3, insert new para. 14.1.4, and amend Annex 14 para. 6 to address vehicles of categories X and Y and conventional vehicles equipped with an Automated Driving System, extend application to vehicles without driver compartment and manual driving controls, clarify occupant compartment provisions, update electrical connection protection standards, and modify fault indication requirements to include logic signals to ADS and limp home mode activation.

Proposal to insert new paragraphs 0., 0.2. to 0.2.2. to introduce Supplement 1 to the 02 series of amendments taking into account vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, amend footnote 1 to paragraph 1. to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev. 8, and amend footnote 2 to paragraph 5.3.4.1. to reference Annex 3 to that document.

Proposal to insert new paras. 0. and 0.1. introducing Supplement 2 to account for vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, and amend para. 1., footnote 1, to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev. 8, para. 2.

Proposal to insert new paragraphs 0. and 0.1. to 0.1.2. introducing Supplement 10 to the 01 series of amendments to UN R97 to account for vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, to add footnote 1 at the end of paragraph 1.1., and to amend paragraph 32.4. regarding immobilizer setting procedures.

Proposal to insert new paras. 0. and 0.1. to 0.1.3. to introduce Supplement 2 to the 06 series of amendments to take into account vehicles of categories X and Y and conventional vehicles equipped with an Automated Driving System, amend para. 1 and Annex 4F footnote 1 to reference the Consolidated Resolution on the Construction of Vehicles, insert new para. 4.79. defining “occupant compartment”, amend para. 7 footnote 11 and para. 12 footnote 12 to reference the Consolidated Resolution on the Construction of Vehicles, and amend paras. 18.1.7., 18.3.1.15., 18.5.5.1., 18.5.5.7., 18.8.7., and 18.10.2. to include provisions relating to occupant compartment and heating systems.

Proposal to introduce new paragraphs addressing vehicles of category X and vehicles with manual mode operating above 6 km/h equipped with Automated Driving System Feature of Type 2 (ADSF-2). The proposal modifies definitions including “mass in running order,” “passenger,” “member of the crew,” and “automatically-operated service-door.” It inserts new definitions for ADSF-1 and ADSF-2, adds requirements for vehicles equipped with ADSF-2, and amends multiple provisions in Annex 1, Annex 3, Annex 4, Annex 8, Annex 11, and Annex 12 regarding driver’s compartment specifications, door operations, emergency systems, and accessibility features.

Proposal to insert new introductory paragraphs 0. and 0.1. to 0.1.4., amend paragraph 1. – Scope, amend paragraph 1 footnote 1, insert new paragraph 2.10., amend paragraph 4.4.1. footnote 2, amend paragraph 5., and amend paragraph 5.1.4. to UN Regulation No. 121 to take into account vehicles of categories X and Y, as well as vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System.

Proposal to insert new paragraphs 0. and 0.1. to 0.1.4. providing introduction to the 01 series of amendments regarding vehicles of categories X and Y and alignment of provisions for all occupants, amend paragraphs 0.1., 0.1.1., 0.1.3., 1.1. and 2.2., footnote 1 to define terms according to Consolidated Resolution R.E.3., amend paragraph 2.7. to define passenger compartment, amend paragraph 4.4., footnote 2 to reference Consolidated Resolution R.E.3., amend paragraph 5.2.1. to require heating systems in each passenger compartment, insert new paragraphs 12. and 12.1. to 12.2.4. providing transitional provisions, amend Annex 5, paragraph 2. to establish surface temperature requirements and allow manufacturers to justify higher temperatures through safety concept demonstration, amend Annex 5, paragraph 2.1. to limit surface temperature to 70°C for uncoated metal or 80°C for other materials, and delete Annex 5, paragraphs 2.2. and 2.3. Transitional provisions apply: as from official entry into force, Contracting Parties shall not refuse type approvals under the 01 series; as from 1 September 2028, Contracting Parties shall not be obliged to accept approvals to the original version first issued after that date; Contracting Parties shall continue accepting original version approvals first issued before 1 September 2028 and equipment/parts approvals issued under the original version.

Proposal to insert new paragraphs 0., 0.1. to 0.1.2., 1.4., 2.21., and 5.6., amend paragraph 1.1. footnote 1, paragraph 4.4.1. footnote 4, paragraph 5.1.3.4., and paragraph 5.1.3.5., based on GRSG-131-33. The supplement introduces provisions for vehicles of categories X and Y and vehicles equipped with an Automated Driving System, defines Safety Concept, addresses Field of Vision Assistant requirements, and establishes alternative requirements for category X vehicles with manual modes operated on-board the vehicle not using a driver’s seat.

Proposal to amend UN R158 based on GRSG-131-36. The supplement renumbers the introduction’s first paragraph to 0.1, describing the regulation’s purpose for rear visibility and detection devices. New paragraphs 0.2–0.2.3 address vehicles of categories X and Y, including exemptions for automated driving systems and manual operation modes. Paragraph 1.4 is amended to exempt category Y vehicles and category X vehicles without on-board manual modes. Amendments modify paragraphs 5.4.1, 12.4, 15.1.3, 15.1.4, 15.2.2, and Annex 9, paragraph 1.3.3.2, addressing safety concepts, rear-view field vision requirements, and vehicle load specifications.

Proposal to insert new paragraphs 0., 0.1. to 0.1.2. introducing Supplement 4 to extend application of UN R163 to vehicles of categories X and Y, and vehicles with manual mode operating above 6 km/h equipped with an Automated Driving System, based on GRSG-131-40. The amendment clarifies that provisions related to driver and manual driving controls shall not apply if absent in the vehicle unless already covered. For vehicles equipped with an Automated Driving System, no special provisions or exemptions apply in any driving mode. Amendments also update footnote references to the Consolidated Resolution on the Construction of Vehicles.

Proposal to insert new para. 0.5. to introduce Supplement 1 to take vehicles of categories X and Y into account and vehicles which can be operated either by a driver or an ADS, amend para. 1.1. footnote * to reference ECE/TRANS/WP.29/78/Rev.8, amend para. 1.3. to exclude Vehicle Identification Number, associated vehicle details, location/positioning data, information about any user, and date and time of an event from the scope, and amend para. 5.4. to specify survivability requirements for event data recorders including mounting position and mechanical shock resistance under Option 1 or impact severity demonstration under Option 2 with reference to UN Regulation Nos. 94, 95, and 137.

Proposal to revise definitions for malfunction indication, reference mass, unladen mass, and vehicle user; add provisions for vehicles equipped with an Automated Driving System; establish documentation requirements for vehicle user warning and inducement systems; update testing procedures for in-service conformity and OBD connector location; and specify activation and deactivation mechanisms for vehicle user warning and inducement systems across multiple annexes, with references to WP.29/1045.

Proposal to amend Paragraph 1.4., Footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles; insert new paragraphs 2.10. and 2.11. defining “ADS user” and “Vehicle user”; amend Paragraph 5.5.2., Footnote 4 to update the reference to Annex 3 of the Consolidated Resolution; and amend paragraphs 6.1.2.4.1.6.1. and 6.2.2.4.1.6.1. to specify that engine starting-up on petrol and switching to LPG or CNG after a predetermined period cannot be changed by the vehicle user.

Proposal to amend paragraph 1.1., footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3.); amend paragraph 4.4.1. to establish requirements for a dual-fuel operating mode indicator including visual and audio signals, with restrictions on indicator design and safety alert priority; amend paragraph 4.4.1.1. to require warnings when engine operation is forced to diesel mode and signals to an ADS feature; and amend paragraph 7.1. to specify OBD system requirements for diesel and dual-fuel operation modes, including malfunction detection and driver notification procedures.

Proposal to enable the approval of vehicles equipped with an Automated Driving System and to optimize the measurement accuracy requirements for chassis dynamometer equipment and the measurement acquisition of the intake manifold pressure in system power testing for high-performance vehicles and makes editorial corrections.