Proposal to align with UN R48 08 series of amendments (to introduce the possibility to switch OFF rear position lamps and other lamps when ambient light conditions outside the vehicle are above 7,000 lux in order to avoid unnecessary fuel consumption). The aim of the document is to reach consensus to enable adoption of a proposal during the next GRPE session (88th session in June 2023).

Proposal to correct inconsistencies in the time between the measurement of the end temperature and the end of the Type 1 test at 23°C for the ATCT family criterion check and in the f_jDyno force calculation.

Proposal to harmonize the requirements of the 00, 01, 02 and 03 series of amendments to UN R154 based on the following justifications:

1. Correction of a wrong reference. In Paragraph 3. the functional requirements for the OBD system are included. Paragraph 4. describes the requirements relating to type-approval including the provisions for deficiencies.
2. For Series 02 and 03, SAE J 1979-2 was allowed as a standard for the transmission of OBD relevant information. ISO 14229 was removed from the list of allowed standard. This proposal aligns series 00 and 01 with series 02 and 03.
3. The standards used for transmission of OBD information are maintained by international standardisation bodies (ISO, SAE). The standardisation body maintaining the affected standard has to be informed.
4. Alignment of wording between the first sentence of paragraph 3.2.1.2. (“ambient or engine temperatures”) and the second sentence, where “or engine” was missing to avoid misunderstanding and ambiguity. Engine temperature is sometimes used as a substitute for ambient temperature. In this case, the engine temperature is evaluated once after a longer engine shut off phase. Only in this case an approval is necessary, as this is the only case, where an OBD monitor is disabled for the complete trip.
5. The OBD requirements for Diesel engines in Paragraph 3.3.4 of Annex C5 are limited to Level 1A. The requirements in paragraphs 6.3. (“Failure modes to be tested”) and 6.4. (“OBD system test”), are not limited to Level 1A. This proposal corrects this.
6. Align Paragraph 6.5.1.3. with GTR No.15 to avoid ambiguity.
7. Alignment with Series 01/03. Those allow the use of alternative preconditioning
   methods for Level 2.

Background: Manufacturers design OBD monitoring conditions and functionalities for market specific driving conditions. Reliable monitors need enable conditions, which run the OBD monitors under circumstances, where failure detection works properly. Those enable conditions are not for all monitors represented by a three-phase WLTC, e.g. some monitors require higher load conditions. For those monitors alternative preconditioning methods are necessary.

• UN R154
• Current status regarding reviewing Japan proposal on CoP section
• Current status regarding reviewing Japan proposal on PHEV calculations

• GTR 15: Annex 13
• Current status regarding GTR No.15 Annex 13

Proposal for corrections and clarifications to the amendments in WP.29/2022/41/Rev.1 based on GRPE/2021/21 addressing particle number emissions, including handling of electric vehicles and Conformity of Production.

Proposal for corrections and clarifications to the amendments in WP.29/2022/42/Rev.1 based on GRPE/2021/21 addressing particle number emissions, including handling of electric vehicles and Conformity of Production.

This proposal introduces the new Utility Factor (UF) approach proposed in the Euro 6e emissions type-approval legislation. In addition, as a result of the application of the new tyre labelling Regulation (EU) 2020/7401, this proposal introduces a revised format of the table with tyre energy efficiency classes according to rolling resistance coefficients (RRC), in-line with the format proposed in the Euro 6e emissions type-approval legislation.

This proposal introduces the new Utility Factor (UF) approach proposed in the Euro 6e emissions type-approval legislation. In addition, as a result of the application of the new tyre labelling Regulation (EU) 2020/7401, this proposal introduces a revised format of the table with tyre energy efficiency classes according to rolling resistance coefficients (RRC), in-line with the format proposed in the Euro 6e emissions type-approval legislation.

The current format of the type approval mark illustrated in Annex A3 is not consistent with the requirements of Section 5.2.1, which may unintentionally lead to approval marks not being issued or accepted in the correct format. The proposed amendment to Annex A3 aligns the illustrated approval marks with the requirements of Section 5.2.1 and Schedule 4 of Revision 3 of the 1958 Agreement. This proposal is available with tracked changes in a pdf version and in a .docx format.

Additional information concerning the 08 series of amendments pursuant to UN R154 (WLTP) and work on real-driving emissions testing.