Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points). This proposal was adopted by the GRSP at its 54th session based on document GRSP-54-15-Rev. 1 as reproduced in Addendum 1 (document GRSP/54/Add.1) to the session report.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Modifications primarily to the headform test procedures in accordance with the proposed amendment 2 to GTR No. 9 as amended and adopted by the GRSP as its 54th session (document GRSP-54-09/Rev.1 as amended and reproduced in Annex V to the GRSP session report. The proposal addresses the adult headform test area and bumper test area.