Proposal to:

• Amend para. 6.1.1.2. to differentiate rearview mirror edge requirements between Classes II to VII and Class I,
• amend para. 6.1.1.3. to specify radius of curvature requirements for mirror parts in static contact with spheres,
• amend para. 6.1.1.4. to clarify requirements for protruding parts and introduce a method for determining projection dimensions,
• insert new para. 6.1.1.4.1. to permit determination of component projection either directly or by drawing reference,
• insert new para. 6.1.1.4.2. to specify measurement by maximum sphere distance variation for non-convex surfaces with Figure 1 example,
• amend para. 6.1.1.5. to exempt edges of fixing holes or recesses with diameter or longest diagonal less than 12 mm,
• amend para. 6.1.1.6. to require attachment device design accommodating a cylinder with 70 mm radius (50 mm for L-category vehicles),
• amend para. 6.1.1.7. to exempt exterior mirror parts with Shore A hardness not exceeding 60,
• insert new para. 6.1.1.8. to apply requirements only to rigid supports for interior mirror parts with Shore A hardness less than 50,
• insert new para. 6.1.1.9. to exempt mirrors mounted not less than 2 m above ground at maximum technical permissible mass from para. 6.1.1.3. requirements.

Proposal to align requirements across different series of amendments to UN R46, and to harmonize requirements for components inside and outside the vehicle with those of UN R26 and UN R61. For detailed explanations, see the TF UN-R46 report (GRSG-130-32) distributed at the 130th GRSG session.

Proposal to:

• Amend para. 6.1.1.2. to differentiate rearview mirror edge requirements between Classes II to VII and Class I,
• amend para. 6.1.1.3. to specify radius of curvature requirements for mirror parts in static contact with spheres,
• amend para. 6.1.1.4. to clarify requirements for protruding parts and introduce a method for determining projection dimensions,
• insert new para. 6.1.1.4.1. to permit determination of component projection either directly or by drawing reference,
• insert new para. 6.1.1.4.2. to specify measurement by maximum sphere distance variation for non-convex surfaces with Figure 1 example,
• amend para. 6.1.1.5. to exempt edges of fixing holes or recesses with diameter or longest diagonal less than 12 mm,
• amend para. 6.1.1.6. to require attachment device design accommodating a cylinder with 70 mm radius (50 mm for L-category vehicles),
• amend para. 6.1.1.7. to exempt exterior mirror parts with Shore A hardness not exceeding 60,
• insert new para. 6.1.1.8. to apply requirements only to rigid supports for interior mirror parts with Shore A hardness less than 50,
• insert new para. 6.1.1.9. to exempt mirrors mounted not less than 2 m above ground at maximum technical permissible mass from para. 6.1.1.3. requirements.

Proposal to align requirements across different series of amendments to UN R46, and to harmonize requirements for components inside and outside the vehicle with those of UN R26 and UN R61. For detailed explanations, see the TF UN-R46 report (GRSG-130-32) distributed at the 130th GRSG session.

Proposal to:

• Amend para. 6.1.1.2. to differentiate rearview mirror edge requirements between Classes II to VII and Class I,
• amend para. 6.1.1.3. to specify radius of curvature requirements for mirror parts in static contact with spheres,
• amend para. 6.1.1.4. to clarify requirements for protruding parts and introduce a method for determining projection dimensions,
• insert new para. 6.1.1.4.1. to permit determination of component projection either directly or by drawing reference,
• insert new para. 6.1.1.4.2. to specify measurement by maximum sphere distance variation for non-convex surfaces with Figure 1 example,
• amend para. 6.1.1.5. to exempt edges of fixing holes or recesses with diameter or longest diagonal less than 12 mm,
• amend para. 6.1.1.6. to require attachment device design accommodating a cylinder with 70 mm radius (50 mm for L-category vehicles),
• amend para. 6.1.1.7. to exempt exterior mirror parts with Shore A hardness not exceeding 60,
• insert new para. 6.1.1.8. to apply requirements only to rigid supports for interior mirror parts with Shore A hardness less than 50,
• insert new para. 6.1.1.9. to exempt mirrors mounted not less than 2 m above ground at maximum technical permissible mass from para. 6.1.1.3. requirements.

Proposal to align requirements across different series of amendments to UN R46, and to harmonize requirements for components inside and outside the vehicle with those of UN R26 and UN R61. For detailed explanations, see the TF UN-R46 report (GRSG-130-32) distributed at the 130th GRSG session.