Report on the third inter-laboratory study evaluating the repeatability and reproducibility of particulate emission factors using GTR 24 (1st amendment) across 14 laboratories worldwide. The study assessed laboratory proficiency in brake particulate matter and particle number emissions measurements for light-duty vehicles, testing two low-metallic brakes and one low-emitting NAO brake using the WLTP-Brake cycle. Inter-lab coefficient of variation for PM₁₀ was 10-15% for low-metallic brakes (4.5-8.5 mg/km emission levels) and 30% for the NAO brake (1.5 mg/km). Intra-lab repeatability for PM₁₀ was less than 5% for low-metallic brakes but higher for the NAO brake. A success rate of 94.8% was achieved after applying quality checks, confirming GTR 24 suitability for regulatory testing. The report provides recommendations for GTR 24 amendments including friction work calculation methodology, torque quality metrics, sampling probe setup standardization, and residual torque limits.
Final status report on development of a new UN Global Technical Regulation addressing particle matter (PM) and particle number (PN) emissions from heavy-duty vehicle brake systems. The GTR introduces brake emissions groups based on design and performance characteristics, establishes test parameters for disc and drum brakes across five diameter groups, defines the World Harmonized Heavy-Duty Brake Cycle (WHBC) comprising 246 brake events over 5:39 hours, specifies brake dynamometer hardware requirements with enclosure dimensions of 1950 mm length, 1000 mm height, and 700 mm depth, requires PM10 and PM2.5 gravimetric measurement and particle number counting, and prescribes a friction braking share coefficient (c-factor) of 1 pending availability of additional data. A preliminary interlaboratory study confirms test cycle reproducibility and particle measurement repeatability, with recommendations to specify fixed enclosure and duct dimensions for improved cross-laboratory consistency.
Overview of documents and working party activities for the 95th session of the Working Party on Pollution and Energy (GRPE). Documents address improvements to UN R179 (Laboratory Measurement of Brake Emissions for Light Duty Vehicles) including handling of vehicles with limited speed, brake replacement parts regulation, and GTR 24 (Measurement procedures for Brake corner emission factors). Related documents also cover a new regulation for heavy-duty brake emissions and a new global technical regulation for heavy-duty brakes. Working documents ECE/TRANS/WP.29/GRPE/2026/29, ECE/TRANS/WP.29/GRPE/2026/30, ECE/TRANS/WP.29/GRPE/2026/31, ECE/TRANS/WP.29/GRPE/2026/32, and ECE/TRANS/WP.29/GRPE/2026/53 are submitted.
Proposal to amend UN GTR No. 25 by modifying requirements for State-of-Certified Energy (SOCE) monitors, battery performance requirements, in-use verification procedures for Parts A, B, and C, and related test procedures and annexes. The GTR establishes harmonised methods to determine in-vehicle battery durability performance of Heavy-Duty Pure Electric Vehicles (HD-PEVs) and Heavy-Duty Off-Vehicle Charging Hybrid Electric Vehicles (HD-OVC-HEVs) of categories 1-2 and 2 exceeding 3,855 kg technically permissible maximum laden mass. The document includes tracked changes to Amendment 1 (WP.29/2026/209), with sections subject to discussion or decision indicated in square brackets and strikethrough text denoting proposed deletions.
Report on the 95th GRPE session presenting progress updates for UN GTR No. 21 (Determination of Electrified Vehicle Power), UN GTR No. 22 (In-vehicle Battery Durability for Electrified Light-Duty Vehicles), and UN GTR No. 25 (In-vehicle Battery Durability for Electrified Heavy-Duty Vehicles). The IWG on EVE reported on Phase 4 objectives and amendments for GTR 21 and 22, with consideration targets of March 2028, and Phase 3 amendments for GTR 25 with consideration target of March 2027. Future work includes investigations into charging power curves, development of a new WP.29 resolution on DC Fast Charge Power Curve performance, and an inventory on harmonization of recharging capabilities.
Terms of reference for the IWG on A-LCA, which will develop an internationally harmonised procedure to determine the carbon footprint of automotive products across their life cycle from production to use and disposal. Working items include defining scope according to ISO 14040, conducting inventory analysis, and defining the format and minimum contents of the A-LCA report. The IWG mandate ends in December 2026, with possible adoption of the resolution by WP.29 in November 2026. The group is open to all experts from any country or organisation of WP.29, chaired by Japan and Republic of Korea, with technical secretaries from OICA, E-Mobility Europe, and Japan.
The workshop on frontal impact assessment in Tokyo, 4-6 November 2026, will address robustness, defined as the vehicle’s ability to protect occupants of varying body height, weight, shape, and seating position in real-world relevant collisions by maintaining structural integrity and effective safety systems so that the risk of injury is minimized for all types of people. The agenda includes review of relevant regulations, clarification of roles of ATDs and HBMs, and conceptual ideas for future regulatory upgrades addressing brain injury, soft tissue neck injury, lower leg injury, thorax injury, submarining, abdominal loading, and lower severity collisions. The workshop will develop an HBM-based robustness assessment matrix to complement current ATD-based requirements.