Proposal to:

• Amend para. 6.1.1.2. to differentiate rearview mirror edge requirements between Classes II to VII and Class I,
• amend para. 6.1.1.3. to specify radius of curvature requirements for mirror parts in static contact with spheres,
• amend para. 6.1.1.4. to clarify requirements for protruding parts and introduce a method for determining projection dimensions,
• insert new para. 6.1.1.4.1. to permit determination of component projection either directly or by drawing reference,
• insert new para. 6.1.1.4.2. to specify measurement by maximum sphere distance variation for non-convex surfaces with Figure 1 example,
• amend para. 6.1.1.5. to exempt edges of fixing holes or recesses with diameter or longest diagonal less than 12 mm,
• amend para. 6.1.1.6. to require attachment device design accommodating a cylinder with 70 mm radius (50 mm for L-category vehicles),
• amend para. 6.1.1.7. to exempt exterior mirror parts with Shore A hardness not exceeding 60,
• insert new para. 6.1.1.8. to apply requirements only to rigid supports for interior mirror parts with Shore A hardness less than 50,
• insert new para. 6.1.1.9. to exempt mirrors mounted not less than 2 m above ground at maximum technical permissible mass from para. 6.1.1.3. requirements.

Proposal to amend para. 6.1.1.3. to specify radius of curvature requirements for mirror parts in potential static contact with spheres of specified diameters, and insert new para. 6.1.1.9. providing an exemption from para. 6.1.1.3. requirements for mirrors with lower edges mounted not less than 2 m above ground at maximum technical permissible mass. Based on ECE/TRANS/WP.29/GRSG/2026/26.

Proposal to:

• Insert new para. 6.1.1.9. exempting mirrors with lower edge mounted not less than 2 m above ground at maximum technical permissible mass from requirements of para. 6.1.1.3.,
• Amend para. 6.2.2.1.2. to specify requirements for external surface parts protruding less than 5 mm with blunted outward facing angles,
• Insert new para. 6.2.2.1.2.1. permitting dimension of projection determination by direct measurement or drawing reference,
• Insert new para. 6.2.2.1.2.2. establishing measurement by maximum variation of 100 mm diameter sphere distance,
• Amend para. 6.2.2.1.3. to exempt fixing holes or recesses with diameter or longest diagonal less than 12 mm from radius requirements if blunted,
• Amend para. 6.2.2.1.4. to exempt camera and monitor parts installed outside vehicle made of material with Shore A hardness less than 60,
• Amend para. 6.2.2.1.5. to limit requirements for internal camera and monitor parts made of material with Shore A hardness less than 50 mounted on rigid support to support only,
• Insert new para. 6.2.2.1.6. exempting CMS with lower edge mounted not less than 2 m above ground at maximum technical permissible mass from para. 6.2.2.1.1. requirements. Based on GRSG/110 and GRSG/2026/27.

Proposal to amend para. 6.2.2.1.4. to delete “For”, amend para. 6.2.2.1.5. to specify that requirements of para. 6.2.2.1.1. apply only to the support for parts made of material with Shore A hardness of less than 50 and mounted on rigid support, and insert new para. 6.2.2.1.6. stating requirements of para. 6.2.2.1.1. do not apply to camera monitor systems if their lower edge is mounted not less than 2 m above ground when vehicle is under maximum technical permissible mass load, based on ECE/TRANS/WP.29/GRSG/2026/28.

Proposal to amend para. 6.2.2.1.4. to delete “For”, amend para. 6.2.2.1.5. to clarify that requirements apply only to the support for parts made of material with Shore A hardness of less than 50 mounted on rigid support, and insert new para. 6.2.2.1.6. establishing that requirements do not apply to CMS with lower edge mounted not less than 2 m above the ground when vehicle is under load corresponding to its maximum technical permissible mass.

Proposal to:

• Amend para. 6.2.2.1.4. to exempt parts of the camera and the monitor installed outside the vehicle which are made of a material with a Shore A hardness of less than 60 from the relevant provisions,
• Amend para. 6.2.2.1.5. to apply requirements of para. 6.2.2.1.1. only to the support for parts of the camera and the monitor installed inside the vehicle which are made of a material with a Shore A hardness of less than 50 and which are mounted on a rigid support,
• Insert a new para. 6.2.2.1.6. to provide that the requirements of para. 6.2.2.1.1. do not apply to CMS if their lower edge is mounted not less than 2 m above the ground when the vehicle is under a load corresponding to its maximum technical permissible mass,
• Amend para. 22.33.5. to provide that Contracting Parties shall continue to accept type approvals issued according to the 04, 05 and 06 series of amendments to this Regulation for vehicles and devices for indirect vision which are not affected by changes introduced by the 07 series of amendments.