Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to extend the modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 05 series in order to avoid an unjustified design restriction for approvals under the earlier version of the regulation.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”, to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials, and to enable the type-approval of direction indicators with variable apparent surfaces.

Proposal to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Proposal to introduce new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

Proposal to introduce new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Proposal to correct typographical errors introduced during previous amendment to the regulation (see document WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Proposal to insert the IEC cap sheet number for the new light category LW2 into the regulation.

Presentation from the informal working group on the Simplification of Lighting Regulations (SLR) on prospects for the rationalization of the light-source lighting regulations.

Paragraph 6.2.2 of UN R6 specifies modes for triggering a failure tell-tale. This proposal would remove a specific reference to filament lamps so that the failure modes apply equally to both filament lamps and LED light sources.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to insert the IEC cap sheet numbers assigned for the new light categories WT21W, WTY21W, WT21/7W and WTY21/7W.

Proposal to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps” and to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. This proposal also would extend modifications that introduced provisions for interdependent direction indicator lamps in the 06 series of amendments to UN R48 to the 04 and 05 series in order to avoid an unjustified design restriction for approvals under the earlier versions of the regulation.