Proposal to insert new paras. 0. and 0.1. to 0.1.4. introducing vehicles of categories X and Y and vehicles with manual modes or automated driving systems, amend para. 1(a) footnote 1, para. 2.13., para. 2.25., paras. 5.4.1. and 5.11.1. footnote 2, insert new para. 2.40. defining “Safety Concept”, amend para. 6.2., para. 7., para. 8.2.1.1., Annex 1A para. 5.1., Annex 3 footnote 18, Annex 21 title, Annex 22 title, and Annex 24 including its scope, definitions, and provisions for safety glazing installation on vehicles. This proposal is based on GRSG-131-23-Rev.1.

Proposal to amend and supersede document ECE/TRANS/GRSG/2026/2 to UN R43. Supplement 13 to the 01 series of amendments introduces provisions for vehicles of category X and Y, and vehicles with manual mode operating above 6 km/h equipped with Automated Driving System Feature of Type 2. The amendment extends application to vehicles without driver and manual driving controls. Different manual modes are considered: remote-control operation, seated driver operation for category X, and onboard operation other than seated for category X. Requirements for windscreens, safety glazing, light transmittance, and installation provisions are modified accordingly for these vehicle categories.

Proposal to correct the wording in UN R43 (Safety Glazing). The expert from the European Association of Automotive Suppliers proposes amending paragraph 8.2.1.1. to modify a table listing tests for windscreens and glass panes of various types, including toughened glass, ordinary laminated glass, treated laminated glass, and glass-plastics. The amendment corrects the title of the optical distortion test listed in the table.

Proposal to clarify that transparency requirements under UN R43 apply in both directions (exterior to interior and interior to exterior), addressing the growing use of privacy foils on windscreens and front side windows post-registration, which raises safety concerns regarding driver eye-contact, law enforcement visibility, and driving behaviour enforcement, consistent with the position expressed by GRSG at its 130th session.

Proposal to align UN R43 with a proposed amendment to UN R125 (ECE/TRANS/WP.29/GRSG/2026/23), which resolves a longstanding inconsistency between the lower datum point definition (§5.1.1.3) and the obstruction requirement (§5.1.3) by harmonizing the lower datum point angle from 5° to 4°.

Proposal to exempt ADS vehicles of subcategories X and Y from requirements related to the presence of a human driver and manual driving controls. The proposal permits X and Y vehicles to use alternative materials for windscreens given their 6 kph speed restriction. The proposal further permits translucence levels below 70% for ADS vehicles while an ADS feature is active (i.e., performing the DDT).

Proposal by prepared by the Task Force on Automated Vehicles
Regulatory Screening (TF-AVRS), with the aim to amend and supersede document
ECE/TRANS/GRSG/2025/19

Proposal to resolve such an inconsistency with UN R125 to harmonize the location of the lower datum point (at 5°) of the angle of obstruction requirement in
paragraph 5.1.3. (at 4°).

Proposal from the GRSG task force on Automated Vehicles Regulation Screening to exempt ADS vehicles of subcategories X and Y from requirements related to the presence of a human driver and manual driving controls. The proposal permits X and Y vehicles to use alternative materials for windscreens given their 6 kph speed restriction. The proposal further permits translucence levels below 70% for ADS vehicles while an ADS feature is active (i.e., performing the DDT).

Proposal by TF-AVRS to amend to enable the application of this Regulation to vehicles of categories X and Y

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure per the update and transfer of the device specifications from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to updates and transfer of related provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to specify the requirements for the headform test. This test should not be mandatory for vehicles where the protection of the occupant’s head is not achieved by the glazing itself, rather by a restraint system or other means.

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure per the update and transfer of the device specifications from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal for amendments pursuant to the introduction of a headform impact test.

Proposal from GRSG to align UN R43 with provisions in GTR 6 concerning the exemption of possible opaque obscuration areas from Zone I of the test area on the windscreen of M₂, M₃ and N categories of vehicles and to correct a reference in the draft Supplement 11 to the 01 series of amendments to the “Test Area B defined in Annex 18” to Annex 21.

Proposal to correct a reference in the draft Supplement 11 to the 01 series of amendments to the “Test Area B defined in Annex 18”, which actually is meant to refer to Annex 21.

Proposal to align UN R43 with provisions in GTR 6 concerning the exemption of possible opaque obscuration areas from Zone I of the test area on the windscreen of M₂, M₃ and N categories of vehicles. This proposal updates and supersedes document GRSG/2023/7.

Proposal to align UN R43 with provisions in GTR 6 concerning the exemption of possible opaque obscuration areas from Zone I of the test area on the windscreen of M₂, M₃ and N categories of vehicles.

Proposal from GRSG to clarify the classification of panes in “safety-glass faced with plastics material” and “glass-plastics” and to resolve a potential inconsistency in abrasion test requirements for flexible plastics other than the windscreen.

Proposal to clarify the classification of panes in “safety-glass faced with plastics material” and “glass-plastics”

Proposal to clarify the scope of the regulation.

Proposal to solve a potential inconsistency regarding abrasion test requirements for flexible plastics other than windscreen.

Proposal to amend paragraph 2.5. with the aim to revise the definition of “glass-plastics”.

Proposal for a mutual resolution [No. 4] concerning recommendations on ceramic printed area widths for panoramic sunroof designs.

Proposal to delete the reference to abrasion requirements in Annex 3, paragraph 6.4.1.3. since abrasion resistance is not relevant in the assessment of resistance to weathering.

Proposal to exempt Zone I from opaque obscuration requirements of GTR 6 under certain conditions.

For the discussion of 125 mm ceramic printed area.

Draft recommendations under development within the PSG informal group.

Proposal to delete the reference to abrasion requirements in Annex 3, paragraph 6.4.1.3. since abrasion resistance is not relevant in the assessment of resistance to weathering.

Proposal to clarify the treatment of extensions of existing approvals under the new transitional provision guidelines (“Until 31 December 2019, Supplement 1, Supplement 4, Supplement 5 and Supplement 6 to the 01 series of amendments to this Regulation may not apply to extensions of approvals that were originally granted prior to the entry into force of Supplement 1, Supplement 4, Supplement 5 and Supplement 6.”)

Proposal to delete the reference to abrasion requirements in Annex 3, paragraph 6.4.1.3. since abrasion resistance is not relevant in the assessment of resistance to weathering.

Proposal to amend Annex 7 (laminated-glass panes), inserting a new paragraph 6 to allow optional 2,260 g ball test and headform test for laminated-glass panes. The proposal adds the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test. The proposal aims to enable the approval of laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle.

Proposal as finalized during the April 2018 GRSG session to amend Annex 7 (laminated-glass panes), inserting a new paragraph 6 to allow optional 2,260 g ball test and headform test for laminated-glass panes. The proposal adds the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test. The proposal aims to enable the approval of laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle.

Proposal to amend GRSG/2018/7 by adding the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test.

Proposal to clarify the text of document GRSG/2018/7 submitted to enable the approval of the laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle. The proposal would amend Annex 7 (laminated-glass panes), inserting a new paragraph 6. to allow optional 2,260 g ball test and headform test for laminated-glass panes.

Proposal to amend Annex 7 (laminated-glass panes), inserting a new paragraph 6. to allow optional 2,260 g ball test and headform test for laminated-glass panes. The proposal aims to amend UN R43 to enable the approval of the laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle.

Proposal to align UN R43 with GTR 6 and UN R125 with regard to the aiming positions of the driver’s eyes. This proposal corrects inconsistencies introduced during the transposition of GTR 6 into UN R43.

Proposal to correct document GRSG/2017/15 based upon comparison against GTR No. 6. The table being revised is in Annex 18 (not 21). This proposal further corrects several values in the table per the original table developed under GTR 6.

Proposal to align UN R43 with values in GTR No. 6 and UN R125 with regard to the aiming positions of the driver’s eyes.. This document complements and completes the proposal in document GRSG/2017/15.

Proposal to align the headform test with the deceleration measurement and the test of resistance to abrasion with ISO 15082:2016-11, including changes to the test details, correction of the headform calibration values, and the introduction of abrasion reference materials. The latter is combined with an abrasive-wheel qualification and a correction calculation (for plastic materials only).

The proposal also amends Figure 2a of Annex 21 to better reflect the meaning of paragraph 2.4.2.2. of Annex 21, mainly to clarify the lateral limits of any opaque obscuration in this area.

Proposal for editorial corrections to align the definition on plastic glazing between the original English version and the French translation as well as of the communication annex on principal/secondary characteristics for laminated-glass windscreens.

Proposal for editorial corrections to align the definition on plastic glazing between the original English version and the French translation as well as of the communication annex on principal/secondary characteristics for laminated-glass windscreens.

Proposal to align UN R43 with GTR 6 and UN R125 with regard to the aiming positions of the driver’s eyes. This proposal corrects inconsistencies introduced during the transposition of GTR 6 into UN R43.

Proposal to align UN R43 with GTR 6 and UN R125 with regard to the aiming positions of the driver’s eyes. This proposal corrects inconsistencies introduced during the transposition of GTR 6 into UN R43.

Proposal for editorial corrections to align the definition on plastic glazing between the original English version and the French translation as well as of the communication annex on principal/secondary characteristics for laminated-glass windscreens.

Proposal to align the headform test with the deceleration measurement and the test of resistance to abrasion with ISO 15082:2016-11, including changes to the test details, correction of the headform calibration values, and the introduction of abrasion reference materials. The latter is combined with an abrasive-wheel qualification and a correction calculation (for plastic materials only).

Proposal to amend Figure 2a of Annex 21 to better reflect the meaning of paragraph 2.4.2.2. of Annex 21, mainly to clarify the lateral limits of any opaque obscuration in this area.

Proposal to align the requirements for plastic panes other than windscreens with the requirements of plastic pane windscreens. This includes amendments concerning rigid plastic panes, flexible plastic panes and rigid plastic multiple-glazed units. The proposed modifications to this type of glazing are in line with the requirements of Supplement 4 to the 01 series of amendment of UN Regulation No. 43.

Copy of the progress report delivered the GRSG during its October 2016 session (as document GRSG-111-32).

Proposal to replace the current Figure 2a with a more accurate drawing reflecting the meaning of paragraph 2.4.2.2 of the regulation. The new drawing addresses the lateral limits of any opaque obscuration of the window area.

The text of the German proposal (document GRSG/2016/21) in the tables in annexes 14 and 16 only refers to small windows as “windows into which a circle of diameter D < 150 mm is capable of being scribed”. OICA proposes to add the criterion of a maximum area limited to 200 cm² in order to align with the definition in paragraph 2.39 (“pane having an area of less than 200 cm² and within which it is not possible to inscribe a circle having a diameter of 150 mm”).

Proposal concerning document GRSG/2015/22 to clarify the specification of the abrasion test machine.

Proposal to align the requirements for plastic panes other than windscreens with the requirements of plastic pane windscreens. This includes amendments concerning rigid plastic panes, flexible plastic panes and rigid plastic multiple-glazed units. The proposed modifications to this type of glazing are in line with the requirements of Supplement 4 to the 01 series of amendment of UN Regulation No. 43.

The US safety agency raises questions concerning the specific nature of the observed failures and the scope of the test procedures to ensure that glazing with ceramic printed areas resist such failures. NHTSA notes anomalies in the data that might suggest failure modes specific to particular manufacturers and/or production batches while questioning the focus on panoramic sunroofs rather than all glazing where ceramic printing might be a potential cause of failure.

Comments on proposed changes to the draft as of 25 April 2016.

Consolidated revision of GTR No. 6.

Figure illustrating proposal for the definition of sunroof configurations requiring additional testing.

Presentation on NHTSA defect investigations into sunroof breakage incidents since 2004.

Proposal for testing of panoramic sunroof glass ceramic printed area (CPA).

Reproduction of the proposal submitted to GRSG in order to clarify the intended scope of the regulation and to align the drop ball test language with that of UN Regulation No. 43 and ISO ISO 3537.

Comparison of the 227g ball impact test across UN R43, Japan “Safety Regulations for Road Vehicles, Article 29”, US FMVSS 205-ANSI/SAE Z26.1-1996, and GTR No. 6.

Clarification that the proposal to exclude multi-layer glazed windows from the head impact requirements of UN R43 does not directly relate to the work or recommendations of the Informal Group on Plastic Glazing.

Proposal to clarify the specification of the abrasion test machine.

Proposal to clarify the specification of the abrasion test machine.

Proposal to define a reduced vision zone I for vehicles of categories M and N other than M₁.

This proposal aims to enable the use of thick glass panes for multiple glazed units which, in turn, requires exempting such configurations from the head-form test.

Proposal of the Informal Group on Plastic Glazing (IGPG) as approved by the GRSG to introduce new provisions for windscreens and for laminated plastic panes other than windscreens.

Proposal as approved by the GRSG to correct Paragraph 5.3.1. to refer to Appendix 10 rather than to Appendix 8 of Annex 1. of UN R43.

Pursuant to its defect investigations concerning the shattering of certain panoramic sunroofs, Korea proposes the establishment of an informal working group to prepare amendments to UN Regulation No. 43 and GTR No. 6 to specify test methods for evaluating panoramic sunroof glazing.

The main objective of this proposal is to develop an amendment to UN GTR No. 6 on Safety Glazing concerning clarification of the methods (e.g. 227g ball drop test), etc. for testing and evaluating the mechanical strength of toughened glass so that the safety of a panoramic sunroof is assured.

Paragraph 5.3.1. refers to Appendix 8 of Annex 1. OICA believes that the reference should be to Appendix 10 of Annex 1 and so proposes this correction.

This proposal aims to enable the use of thick glass panes for multiple glazed units which, in turn, requires omitting the head-form test in case of these units.

OICA and CLEPA comments on the Korean proposal to amend GTR No. 6 and UN Regulation No. 43 in response to issues identified in its defect investigation concerning panoramic sunroofs.

Proposal for an amendment to UN Regulation No. 43 to define a “reduced vision zone I” for vehicles of categories M and N other than M1. The goal is to extend the concept that already exists for M1 vehicles in order to enable the installation of sensors and cameras that improve driving safety.

Explanations and arguments in support of the amendments to UN R43 proposed by the Informal Group on Plastic Glazing (IGPG) in document GRSG/2014/23.

Proposal to amend the test methods for toughened glass pursuant to Korean defect investigations involving the ceramic printed area of certain panoramic sunroofs.

Working draft text of amendments to UN R43 as developed by the Informal Group on Plastic Glazing through its 10th session.

Draft report on the 10th meeting of the GRSG informal group on the introduction of plastic glazing for windscreens and laminated plastic panes other than windscreens in UN Regulation N°43.

Proposal to clarify the testing method for resistance to high temperature in order to address issues raised with testing at high altitudes and to clarify the requirements of Annex 21 (provisions on the installation of safety glazing on vehicles) based on recommendations from the Informal Group on Plastic Glazing (IGPG).

Proposal to define “small glazing” and to exempt such small glazing from headform testing.

Text prepared by Germany on behalf of the Informal Group on Plastic Glazing (IGPG) to introduce new provisions for windscreens and for laminated plastic panes other than windscreens.

This proposal corrects an editorial mistake in the tolerances of Annex 6. In Annex 10, paragraph 3.2.2.2. and in Annex 12, paragraph 3.2.2., the correct tolerance should read: 1.5m +0/-5mm. (The same tolerances also appear in UN GTR No. 6, paragraphs 5.4.3. and 6.5.4.2.)

Presentation on Korean investigations that identify certain conditions under which ceramic printing (black enamel) weakens toughened glass such that the glass no longer meets the mechanical strength requirements of GTR 6, UN R43 or FMVSS 205. Korea proposes amending the UN glazing regulations.

Proposal by the IGPG working group to introduce provisions for plastic glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43, superseding document GRSG-104-43.

Test to determine whether a plastic safety glazing material meets minimum resistance thresholds from the action of a wiper, including dirt, at ambient temperatures.

Presentation on the results of research into wiper testing of plastic glazing including correlation of results with real world data.

CLEPA comments on the OICA proposal for Supplement 3 to the 01 series of amendments to Regulation No. 43 (document GRSG/2014/14) that seeks to avoid imposing administrative burdens on small glazing that is not required for the driver’s forward or rearward field of vision.

Presentation on Korea’s automotive safety agencies, recall system, and investigation into shattering of panoramic sunroofs.

Proposal to introduce provisions for the use of plastic safety glazing in side windows behind the B pillar more in line with the stipulations for glazing with a light transmittance below 70 per cent in that area.

Proposal to clarify the testing method for resistance to high temperature in order to address issues raised with testing at high altitudes. CLEPA proposes to amend the wording of paragraph 5.1. to clarify how to proceed with a test in boiling water, which is permitted for safety glazing with both external surfaces of inorganic material. The tolerance of +0 °C / -2 °C is taken from ISO 3917, high temperature test. The temperature of boiling water can be determined with the required accuracy easily.

Proposal to avoid imposing administrative burdens on small glazing that is not required for the driver’s forward or rearward field of vision.

Text prepared by the Informal Group on the Introduction of Plastic Glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43 (IGPG) in order to clarify the requirements of Annex 21 (provisions on the installation of safety glazing on vehicles).

Text prepared to introduce provision to address difficulties encountered by technical services located at high altitudes in fulfilling the barometric pressure conditions required for the impact test. This document supersedes informal document GRSG-105-24.

Draft proposal prepared for submission to the Working Party on General Safety to introduce plastic glazing for windscreens and laminated plastic panes other than windscreens into Regulation No. 43.

Proposal from the expert from France to improve and re-arrange the wording of the text of the regulation in accordance with the informal group proposal for amendments to UN R43 (document GRSG-104-43)

Presentation of proposals for the on-road testing of plastic windscreens and other glazing.

Working document for the introduction of plastic glazing approval requirements under UN R43.

Working draft proposal for amendments to UN R43 to introduce provisions for the approval of laminated rigid plastic windscreens.