This document proposes a new UN Regulation on uniform provisions concerning approval of non-original and identical replacement brake parts regarding particulate emissions. The regulation applies to laboratory measurement of brake emissions from non-original replacement brake pads, linings, discs, and drums for vehicles of categories M₁, N₁, and N₂ originating from vehicles with type approval under Regulation No. 179. Approval requires emission factors to comply with specified limits based on vehicle category and powertrain technology. The regulation establishes brake emissions families based on characteristics including calliper type, vehicle axle location, friction material formulation, brake disc or drum material, disc surface form, friction material surface area, and drum diameter. Testing procedures, conformity of production requirements, marking and packaging specifications, and approval extension procedures are detailed.

TF 3c addressed brake emission of replacement parts. Proposed amendments include clarification that surface heat-treated discs fall under “other” category, refinement of “Brake Emissions Family Parent” definition, and addition of new appendix to UN Regulation No. 179 Annex 2. Data sharing agreement established: front-to-rear axle emission ratio, brake force distribution, and vehicle electrification type will be shared with aftermarket operators. Two approaches for aftermarket applicants: use vehicle-specific data through benchmarking or bilateral agreements, or apply default values from Tables 5.4 and 5.5. Testing revealed up to 30% variation within friction-couple families. Safety factor application when using actual c-factor values remains under discussion, with final decision expected before October.

Draft Minutes of the 56th Particle Measurement Programme session held online on 9th July 2026, 12:00-14:30 CET. The meeting reviewed amendments to Brakes GTR 24 and UN R179 across five task forces. TF3a presented layout and testing topics with concerns raised regarding repetition increases and force distribution. TF3b discussed vehicles with limited speed and family classification issues. TF3c addressed brake replacement parts and emission limits. TF4 reported on electromechanical brakes with work package B agreed. TF5 presented the GTR on heavy-duty brake particle emissions with results expressed in mg/km, with some points remaining in brackets pending inter-laboratory comparisons. Comments are due by 16th July, with the next meeting expected mid/end of September 2026 and a hybrid PMP meeting planned for 12th or 13th October in Geneva.

PMP webex meeting scheduled for 9th July 2026, 12:00–14:30 CET. Agenda includes an overview of amendments to Brakes GTR 24 and UN R179, task force discussions on layout and testing topics, vehicles limited speed, brake replacement parts, electromechanical brakes GTR and UNR, HD brakes, projects on tyres and brakes, and any other business. Webex meeting access details and link provided.

The 56th PMP session convened online on 7 May 2026 with approximately 70 participants. Meeting minutes from 13 March 2026 were accepted. PMP agreed on a joint neutral template for all task forces. TF3a discussed cooling air adjustment, temperature criteria, and vehicle emission factors, with proposals requested by end of May 2026. TF3b will discuss family building and speed-limited vehicles. TF3c presented brake replacement parts activities. TF4 prepared work package B on electromechanical brakes and requested feedback by end of May 2026. TF5 reported progress on GTR on HD brake particle emissions with test campaigns planned. The next meeting is expected end of June or beginning of July 2026.

At the 94th session of GRPE, CLEPA proposed a draft UN Regulation for approval of replacement brake parts. A dual pathway approach was proposed with two options depending on data availability: fully available data or minimal set of data with worst-case assumptions. PMP Task Force 3c was established to prepare a UN Regulation for approving replacement brake parts regarding particle emissions. The TF3c will define minimum information required under the simplified approach, assess variability within a family, and identify worst-case assumptions. CLEPA presented two approval concepts and requested support for Option A only. The next meeting is scheduled for 18 May 2026.

The PMP webex meeting scheduled for 7 May 2026, 12:00-14:30 CET will review meeting minutes from 13.03.2026, provide an overview of amendments to Brakes GTR 24 and UN R179 covering layout and testing topics, vehicle limited speed, brake replacement parts, and electromechanical brakes, discuss GTR HD brakes, and address any other business.

The PMP session discussed revisions to the group’s terms of reference to address overlapping technical issues with GTR 24, UN R179, and replacement parts regulations. Three task forces were proposed: TF3a on layout and testing, TF3b on speed-limited vehicles, and TF4 on electromechanical brakes. Topics included non-original brake parts regulations, UN R179 amendments for new vehicle categories, and GTR heavy-duty brake particle emissions standards. The next meeting was scheduled for end of April 2026.

This document is also available with tracked changes.

Proposal to establish approval requirements for the particle emissions of replacement brake pads (based on the laboratory method established by GTR 24).

Proposal to enable the approval of vehicles equipped with an Automated Driving System under this Regulation.