Proposal to add a paragraph to define the purpose of the “SS” marking introduce by the amendments to UN R106 on agricultural and related off-road tyres.

Proposal as approved by GRRF to add tyre sizes and tyre classification codes common in the United States and standardised by the Tire and Rim Association, but needed under UN Regulation No. 106 in order to permit their type approval in conformity with Regulation EU 167/2013 for imported tyres. The proposal adds kPa marking specifications for use in measurements and tyre testing. The proposal further includes changes to the text and addition of tyre size designations to Annex 5 and Annex 7:

1. Paragraph 2.33.2 deleted since new tables for IF and VF were added to Annex 7
2. Paras 3.2., 3.2.2. and 5.4. modified because “tyres submitted for approval” cannot bear an approval mark until approved and the “only” as it is written can be misunderstood. Para. 3.2.2. was aligned to the wording in other UN Regulations. Reference to para. 3.3 in paragraph 5.4. is deleted because paragraph 3.3 does not refer to specific markings
3. Para 6.1.2. amended to align the wording to the headers in Annex 5 and to correct the reference to the footnote
4. Para 6.2.1. amended to restore the proper references after renumbering resulting from the latest Supplements
5. The amendment of Annex 5, Table 5 adds the value for the overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”
6. Annex 5, Table 6, Note 1 amended because most of the tyre sizes listed in the table, especially those identified by the “classification code I‐3” (i.e. Traction tread), are currently available in both versions: ‘implement’ to be used on agricultural machinery and ‘IND’ to be used on construction vehicles. The two types of tyres have the same type of size designation and the same dimensions. Therefore some manufacturers identify those tyres with the suffix ‘IND’ rather than with the suffix ‘IMP’ thus applying the variation of load capacity with speed as published in Annex 7 Part E. The reason for this proposal is to avoid a duplication of tables with a new table only replacing the suffix IMP with the suffix IND.
7. The addition of the footnote to Annex 5, Table 7 answers the request by GRRF to introduce appropriate formulae in the Regulation instead of continuously updating Annex 5.
8. References in Annex 7 corrected pursuant to the renumbering following the introduction of three new paragraphs in Supplement 15 approved during the 172nd session of WP.29.
9. Annex 7, Part A amended to conform with Tire and Rim Association specifications for code designated diagonal tyres with speed symbol A8.

This document consolidates previous documents GRRF/2017/19 and informal document GRRF-84-17 taking into account the request for addition of tyre sizes and tyre classification codes common in the United States and standardised by the Tire and Rim Association, but needed to be added to UN Regulation No. 106 in order to permit their type approval in order to conform to Regulation EU 167/2013 for tyres to be exported to Europe. It includes addition/modifications of some paragraphs to the main text of the Regulation as well as the addition of some tyre size designations to Annex 5 and Annex 7:

1. ISO 4251-4 replaced by ISO 18805
2. Paragraph 2.33.2 deleted since new tables for IF and VF were added to Annex 7
3. Paras 3.2., 3.2.2. and 5.4. modified because “tyres submitted for approval” cannot bear an approval mark until approved and the “only” as it is written can be misunderstood. Para. 3.2.2. was aligned to the wording in other UN Regulations. Reference to para. 3.3 in paragraph 5.4. is deleted because paragraph 3.3 does not refer to specific markings
4. Para 6.1.2. amended to align the wording to the headers in Annex 5 and to correct the reference to the footnote
5. Para 6.2.1. amended to restore the proper references after renumbering resulting from the latest Supplements
6. The amendment of Annex 5, Table 5 adds the value for the overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”
7. Annex 5, Table 6, Note 1 amended because most of the tyre sizes listed in the table, especially those identified by the “classification code I‐3” (i.e. Traction tread), are currently available in both versions: ‘implement’ to be used on agricultural machinery and ‘IND’ to be used on construction vehicles. The two types of tyres have the same type of size designation and the same dimensions. Therefore some manufacturers identify those tyres with the suffix ‘IND’ rather than with the suffix ‘IMP’ thus applying the variation of load capacity with speed as published in Annex 7 Part E. The reason for this proposal is to avoid a duplication of tables with a new table only replacing the suffix IMP with the suffix IND.
8. The addition of the footnote to Annex 5, Table 7 answers the request by GRRF to introduce appropriate formulae in the Regulation instead of continuously updating Annex 5.
9. References in Annex 7 corrected pursuant to the renumbering following the introduction of three new paragraphs in Supplement 15 approved during the 172nd session of WP.29.
10. Annex 7, Part A amended to conform with Tire and Rim Association specifications for code designated diagonal tyres with speed symbol A8.

Proposal to add markings for the inflation pressure to be used for measurements and tests.

Consolidated version of UN R106 including ETRTO proposed amendments (see documents GRRF/2018/6 and GRRF/2018/7).