GRE
Session 76 | Geneva | 25-28 Oct 2016
4. Simplification of lighting and light-signalling Regulations
GRE-75-06 | Status of pending GRE proposals with regard to the simplification of lighting regulations
GRE/2016/30 | Proposal for a collective amendment to Regulations Nos. 4, 6, 7, 23, 38, 50, 77, 87, 91 and 119 This proposal removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s). From an electronic point of view, the information of the wattage brings no benefit and is confusing if the same module is used in different systems and at different wattages.
GRE/2016/32 | Proposal for a collective amendment to Regulations Nos. 19, 98, 112, 113 and 123 This collective amendment on the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, clarifies the test cycle and also aligns the requirements of Regulations Nos. 19, 98, 112, 113 and 123. In addition to resolving problems of interpretation presented by the current text, this collective amendment will assist the Informal Working Group "Simplification of Lighting and Light-Signalling Regulations" in drafting the new simplified Regulations which is underway.
GRE/2016/25 | Proposal for a collective amendment to Regulations Nos. 98, 112 and 123 Supplement 3 to the 01 series of amendments to UN R 98, 112, and 123 deleted the measurement point HV from the photometric requirement table. The HV measurement point, however, remains a requirement for checking photometric stability. This proposal removes the HV measurement point from the photometric stability requirements for the passing beam. The HV measurement point remains a valid for the driving beam.
GRE/2016/31 | Proposal for a collective amendment to Regulations Nos. 7, 23, 38, 48, 77, 91 and 119 The current requirements on light source failure in lamps equipped with multiple light sources differ across UN Regulations. GTB submitted and then withdrew a proposal to align these requirements (GRE/2016/13). This updated proposal improves upon the text of the previous proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.
GRE/2016/34 | Proposal for a collective amendment to Regulations Nos. 19, 98, 112, 113 and 123 This collective amendment extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123 (as presented in the previous session document GRE-75-14). The proposal would allow for the use of regulated replaceable LED light sources according to Regulation No. 128 in all applications where the use of LED modules is already permitted.
GRE-76-07 | Correction to document GRE/2016/31 Correction to the proposal for a collective amendment to Regulations Nos. 7, 23, 38, 48, 77, 91 and 119. Since the cornering lamp projects a beam to the left and right of the reference axis, it is not relevant to check the photometric values in the reference axis (HV). Therefore, the test point at 2.5°D, 45°L or R shall be used.
GRE-76-13 | Upcoming changes to Regulation No. 128 related to LED Light Sources for Forward Lighting Applications The collective amendment presented in GRE/2016/34 extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123. The introduction of LED light source categories under UN R128 for forward lighting applications (front fog, low beam, high beam, AFS) is planned for 2017. This presentation explains the plans, timeline, and dependencies GTB proposes to address through the collective amendment, especially within the context of the simplification of lighting regulations program.
GRE-76-22/Rev.1 | Revision of document ECE/TRANS/WP.29/GRE/2016/31 Revised proposal (removing the section on UN R48 and incorporating corrections noted in document GRE-76-07) to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required. This collective amendment addresses Regulations Nos. 7, 23, 38, 77, 91 and 119. The proposals concerning UN R48 will be resubmitted for consideration during the 77th GRE session.
GRE-76-23 | Simplification of Lighting and Light-Signalling Regulations: status update and next steps
GRE-76-24/Rev.1 | Simplification of Lighting and Light-Signalling Regulations: application of the Unique Identifier (UI)
GRE-76-11 | Exchange of communications between the secretariat and OLA Exchange of communications between the secretariat and the UN Office of Legal Affairs concerning the simplification of lighting and light-signalling Regulations (SLR). GRE proposed to consolidate around 30 Regulations on different individual lighting and light-signalling devices (lamps) into three new Regulations (forward lighting, light-signalling, and retro-reflective devices). OLA provides general comments in response to GRE questions intended to ensure that the selected approach respects the legal and administrative requirements of UN treaties and specifically the 1958 Agreement.
WP.29/2013/68 | Proposal for Supplement 15 to the 02 series of amendments to Regulation 3 Proposal to update the Conformity of Production provisions.
WP.29/2013/69 | Proposal for Supplement 17 to Regulation No. 4 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP).
WP.29/2013/71 | Proposal for Supplement 25 to the 01 series of amendments to Regulation No. 6 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP).
WP.29/2013/72 | Proposal for Supplement 23 to the 02 series of amendments to Regulation No. 7 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2013/75 | Proposal for Supplement 6 to the 04 series of amendments to Regulation No. 19 Proposal to complete the deletion of distributed lighting systems (DLS), or rather light generators, from the regulation and to update the Conformity of Production (CoP) requirements
WP.29/2013/76 | Proposal for Supplement 20 to Regulation No. 23 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2013/79 | Proposal for Supplement 17 to Regulation No. 38 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2013/83 | Proposal for Supplement 17 to Regulation No. 50 Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.
WP.29/2013/85 | Proposal for Supplement 6 to the 01 series of amendments to Regulation No. 69 GRE proposal to update the Conformity of Production (CoP) requirements.
WP.29/2013/86 | Proposal for Supplement 9 to the 01 series of amendments to Regulation No. 70 GRE proposal to update the Conformity of Production (CoP) requirements.
WP.29/2013/87 | Proposal for Supplement 17 to Regulation No. 77 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources, and to update the Conformity of Production (CoP) requirements.
WP.29/2013/88 | Proposal for Supplement 18 to Regulation No. 87 GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2013/89 | Proposal for Supplement 16 to Regulation No. 91 Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2013/90 | Proposal for Supplement 5 to the 01 series of amendments to Regulation No. 98 Proposal to amend the provisions concerning the heat test requirements for Conformity of Production (CoP), to complete the deletion of distributed lighting systems (DLS) (light generators) from the regulations, and to update the general CoP requirements.
WP.29/2013/92 | Proposal for Supplement 5 to the 01 series of amendments to Regulation No. 112 Proposal to amend the provisions concerning the heat test requirements for Conformity of Production and to otherwise update the CoP requirements.
WP.29/2013/93 | Proposal for Supplement 3 to the 01 series of amendments to Regulation No. 113 Proposal to update the Conformity of Production (CoP) requirements and to correct provisions on bend lighting for motorcycles recently adopted by WP.29 as Supplement 2 (document WP.29/2012/83).
WP.29/2013/94 | Proposal for Supplement 4 to the 01 series of amendments to Regulation No. 119 Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.
WP.29/2014/31 | Proposal for the new 04 series of amendments to Regulation No. 27 Proposal to clarify the Conformity of Production requirements.
WP.29/2014/32 | Proposal for Supplement 9 to Regulation No. 65 Proposal to clarify the Conformity of Production requirements.
GRE/2013/55/Rev.1 | Proposal for collective amendments to Regulations Nos. 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123 Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.
GRE/2014/3 | Proposal for Collective amendments to Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 65, 77, 87, 91, 98, 104, 112, 113, 119 and 123 Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of "type", with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings. Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.
GRE/2015/7 | Proposal for Supplement 27 to the 01 series of amendments to Regulation No. 6 Proposal to correct an error in Supplement 24 to the 01 series of amendments (document WP.29/2013/14 adopted by the Forum during its March 2013 session). During the compilation of the collective amendment (GRE-68-02-Rev.2), necessary changes to Regulation No. 6 were overlooked. This amendment proposes to align the treatment of categories 1, 1a and 1b with other categories and devices.
GRE/2015/16 | Proposal for Supplement 7 to the 01 series of amendments to Regulation No. 112 Correction of errors found in the references to “left-hand traffic” and “right-hand traffic” in the text and associated diagrams of Annex 2 of the regulation.
GRE/2015/23 | Proposal for a corrigendum to the 01 series of amendments to Regulation No. 112 Proposal to correct an inconsistency between the regulation text and Figure B of Annex 3.
GRE/2016/11 | Proposal for Supplement 26 to the 01 series of amendments to Regulation No. 6 and Supplement 24 to the 02 series of amendments to Regulation No. 7 Proposal to align the text in the header row of the table in paragraph 6.1 (light emitted by the lamps) with the definitions used in Regulation No. 48 for the installation of "single lamps", "lamps marked D" and "interdependent lamps".
GRE/2016/14 | Proposal for a collective amendment to Regulations Nos. 19, 45, 98, 112, 113 and 123 Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of "2 ± 1 parts by weight" of surfactant results in invalid testing. The correct specification should be "2 ± 1 drops" of surfactant. While GTB notes that the specification should eventually be incorporated differently under the pending simplification of lighting regulations, the organization strongly urges amending UN R45 as quickly as possible.
GRE/75 | Report of the GRE on its 75th session
7. (h) Regulation No. 123 (Adaptive front-lighting systems (AFS))
GRE/2016/29 | Proposal for Supplement 8 to the 01 series of amendments to Regulation No. 123 When the 01 series of amendments to Regulation No. 123 was introduced to convert the photometric requirements from illuminance E (lux) to luminous intensities I (cd), some changes from E<sub>max</sub> to I<sub>max</sub> were overlooked. This amendment introduces the necessary corrections. The proposal also amends Annex 3, Table 2 to allow sub-classes of Class C to lower the cut-off position to give the opportunity to adapt to foggy weather conditions and thus avoid glare and increase safety.
GRE/2016/28 | Proposal for Supplement 8 to the 01 series of amendments to Regulation No. 123 During its 69th session, GRE adopted proposals to update the Conformity of Production (CoP) procedures for lighting and light-signalling devices, but decided to await the work of a GTB task force on the simplification of CoP provisions for AFS before addressing UN R123. This proposal amends the CoP procedures in line with those agreed for UN R112 (document GRE/2013/37) to create simplified photometric CoP tables for each class (C, V, W, E, R, RADB) with its applicable 0/20/30 per cent limits. Furthermore, the task force clarified which tests are necessary for CoP testing and which are necessary only for type approval testing. The methods and requirements for the "initial" type approval remained unchanged. An overview of the main AFS characteristics can be found in documents GRE-48-28 and GRE-48-30.
GRE/2013/37 | Proposal for Supplement 5 to the 01 series of amendments to Regulation No. 112 Submitted by Germany in order to update the Conformity of Production (CoP) requirements.
GRE-48-28 | Adaptive Front Lighting Systems (AFS) Overview of AFS development and characteristics.
GRE-48-30 | Adaptive Front Lighting Systems (AFS): History and scientific back-up
GRE-76-14/Rev.1 | Editorial improvement to ECE/TRANS/GRE/2016/29 Editorial improvements to the proposal for Supplement 8 to the 01 series of amendments to UN R123.
GRE-75-15 | Report of the GTB Task Force on Conformity of Production
8. Pending amendment proposals
GRE/73 | Report of the GRE on its 73rd session
GRE/2015/7 | Proposal for Supplement 27 to the 01 series of amendments to Regulation No. 6 Proposal to correct an error in Supplement 24 to the 01 series of amendments (document WP.29/2013/14 adopted by the Forum during its March 2013 session). During the compilation of the collective amendment (GRE-68-02-Rev.2), necessary changes to Regulation No. 6 were overlooked. This amendment proposes to align the treatment of categories 1, 1a and 1b with other categories and devices.
GRE/2015/16 | Proposal for Supplement 7 to the 01 series of amendments to Regulation No. 112 Correction of errors found in the references to “left-hand traffic” and “right-hand traffic” in the text and associated diagrams of Annex 2 of the regulation.
GRE/2015/23 | Proposal for a corrigendum to the 01 series of amendments to Regulation No. 112 Proposal to correct an inconsistency between the regulation text and Figure B of Annex 3.
GRE/2016/11 | Proposal for Supplement 26 to the 01 series of amendments to Regulation No. 6 and Supplement 24 to the 02 series of amendments to Regulation No. 7 Proposal to align the text in the header row of the table in paragraph 6.1 (light emitted by the lamps) with the definitions used in Regulation No. 48 for the installation of "single lamps", "lamps marked D" and "interdependent lamps".
GRE/2016/14 | Proposal for a collective amendment to Regulations Nos. 19, 45, 98, 112, 113 and 123 Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of "2 &plusmn; 1 parts by weight" of surfactant results in invalid testing. The correct specification should be "2 &plusmn; 1 drops" of surfactant. While GTB notes that the specification should eventually be incorporated differently under the pending simplification of lighting regulations, the organization strongly urges amending UN R45 as quickly as possible.
GRE-76-13
Upcoming changes to Regulation No. 128 related to LED Light Sources for Forward Lighting Applications (GTB)
25 Oct 2016 Working Party Informal Documents Light-Emitting Diode Light Sources LED Light Sources Uniform provisions concerning the approval of light emitting diode (LED) light sources for use in approved lamp units on power-driven vehicles and their trailers Front Fog Lamps Front Fog Lamps Uniform Provisions Concerning the Approval of Power-driven Vehicle Front Fog Lamps Headlamps Equipped with Gas-discharge Light Sources Gas-discharge-light Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Equipped with Gas-discharge Light Sources Headlamps Emitting an Asymmetrical Passing Beam Asymmetrical Beam Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting an Asymmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament Lamps and/or Light-Emitting Diode (LED) Modules Symmetrical Beam Headlamps of Filament, Gas-discharge, or LED Type Symmetrical Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting a Symmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament, Gas-discharge light sources or LED Modules Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles The collective amendment presented in GRE/2016/34 extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123. The introduction of LED light source categories under UN R128 for forward lighting applications (front fog, low beam, high beam, AFS) is planned for 2017. This presentation explains the plans, timeline, and dependencies GTB proposes to address through the collective amendment, especially within the context of the simplification of lighting regulations program. GRE-76-0013
GRE-76-14/Rev.1
Editorial improvement to ECE/TRANS/GRE/2016/29 (GTB)
26 Oct 2016 Working Party Informal Documents Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles Editorial improvements to the proposal for Supplement 8 to the 01 series of amendments to UN R123. GRE-76-0014/Rev.1
GRE/2016/25
Proposal for a collective amendment to Regulations Nos. 98, 112 and 123 (GTB)
17 Aug 2016 Working Party Formal Documents Headlamps Equipped with Gas-discharge Light Sources Gas-discharge-light Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Equipped with Gas-discharge Light Sources Headlamps Emitting an Asymmetrical Passing Beam Asymmetrical Beam Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting an Asymmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament Lamps and/or Light-Emitting Diode (LED) Modules Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles Supplement 3 to the 01 series of amendments to UN R 98, 112, and 123 deleted the measurement point HV from the photometric requirement table. The HV measurement point, however, remains a requirement for checking photometric stability. This proposal removes the HV measurement point from the photometric stability requirements for the passing beam. The HV measurement point remains a valid for the driving beam. GRE/2016/0025
GRE/2016/28
Proposal for Supplement 8 to the 01 series of amendments to Regulation No. 123 (GTB)
17 Aug 2016 Working Party Formal Documents Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles During its 69th session, GRE adopted proposals to update the Conformity of Production (CoP) procedures for lighting and light-signalling devices, but decided to await the work of a GTB task force on the simplification of CoP provisions for AFS before addressing UN R123. This proposal amends the CoP procedures in line with those agreed for UN R112 (document GRE/2013/37) to create simplified photometric CoP tables for each class (C, V, W, E, R, RADB) with its applicable 0/20/30 per cent limits. Furthermore, the task force clarified which tests are necessary for CoP testing and which are necessary only for type approval testing. The methods and requirements for the "initial" type approval remained unchanged. An overview of the main AFS characteristics can be found in documents GRE-48-28 and GRE-48-30. GRE/2016/0028
GRE/2016/29
Proposal for Supplement 8 to the 01 series of amendments to Regulation No. 123 (GTB)
12 Aug 2016 Working Party Formal Documents Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles When the 01 series of amendments to Regulation No. 123 was introduced to convert the photometric requirements from illuminance E (lux) to luminous intensities I (cd), some changes from E<sub>max</sub> to I<sub>max</sub> were overlooked. This amendment introduces the necessary corrections. The proposal also amends Annex 3, Table 2 to allow sub-classes of Class C to lower the cut-off position to give the opportunity to adapt to foggy weather conditions and thus avoid glare and increase safety. GRE/2016/0029
GRE/2016/32
Proposal for a collective amendment to Regulations Nos. 19, 98, 112, 113 and 123 (GTB)
12 Aug 2016 Working Party Formal Documents Front Fog Lamps Front Fog Lamps Uniform Provisions Concerning the Approval of Power-driven Vehicle Front Fog Lamps Headlamps Equipped with Gas-discharge Light Sources Gas-discharge-light Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Equipped with Gas-discharge Light Sources Headlamps Emitting an Asymmetrical Passing Beam Asymmetrical Beam Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting an Asymmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament Lamps and/or Light-Emitting Diode (LED) Modules Symmetrical Beam Headlamps of Filament, Gas-discharge, or LED Type Symmetrical Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting a Symmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament, Gas-discharge light sources or LED Modules Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles This collective amendment on the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, clarifies the test cycle and also aligns the requirements of Regulations Nos. 19, 98, 112, 113 and 123. In addition to resolving problems of interpretation presented by the current text, this collective amendment will assist the Informal Working Group "Simplification of Lighting and Light-Signalling Regulations" in drafting the new simplified Regulations which is underway. GRE/2016/0032
GRE/2016/34
Proposal for a collective amendment to Regulations Nos. 19, 98, 112, 113 and 123 (GTB)
17 Aug 2016 Working Party Formal Documents Front Fog Lamps Front Fog Lamps Uniform Provisions Concerning the Approval of Power-driven Vehicle Front Fog Lamps Headlamps Equipped with Gas-discharge Light Sources Gas-discharge-light Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Equipped with Gas-discharge Light Sources Headlamps Emitting an Asymmetrical Passing Beam Asymmetrical Beam Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting an Asymmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament Lamps and/or Light-Emitting Diode (LED) Modules Symmetrical Beam Headlamps of Filament, Gas-discharge, or LED Type Symmetrical Headlamps Uniform Provisions Concerning the Approval of Motor Vehicle Headlamps Emitting a Symmetrical Passing Beam or a Driving Beam or Both and Equipped with Filament, Gas-discharge light sources or LED Modules Adaptive Front-lighting Systems Adaptive Front-lighting Systems Uniform Provisions Concerning the Approval of Adaptive Front-lighting Systems (AFS) for Motor Vehicles This collective amendment extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123 (as presented in the previous session document GRE-75-14). The proposal would allow for the use of regulated replaceable LED light sources according to Regulation No. 128 in all applications where the use of LED modules is already permitted. GRE/2016/0034