Draft version of the proposed UN Regulation that would transpose Global Technical Regulation No. 14 on pole side-impact protection into the type-approval system of the 1958 Agreement. This draft is presented for informational purposes only pending submission of a final document for consideration by the GRSP.

24. The expert from Australia introduced, for information to GRSP, a draft proposal (GRSP-54-14) for a UN Regulation to transpose the UN GTR on pole side impact into the 1958 Agreement. He urged adopting the proposal in 2014 and that for this task, the IWG on pole side impact was no longer needed. He also underlined that the scope of the proposal was different from that of the UN Regulation No. 95 as well as having different dummies and injury criteria. Therefore, he suggested that the proposal would be a new UN Regulation instead of an amendment to UN Regulation No. 95. GRSP agreed by consensus to resume consideration on this matter at its May 2014 session on the basis of a proposal of a new UN Regulation voluntarily prepared by the expert from Australia.

Draft text transposing GTR No. 14 on pole side impact protection into a UN Regulation under the 1958 Agreement. A proposal for the 01 series of amendments (document GRSP/2014/12) has also been prepared to enable the Contracting Parties applying this Regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.

34. The expert from Australia summarized (GRSP-55-16) the work of transposing UN GTR No. 14 (Pole Side Impact) into a draft new UN Regulation (ECE/TRANS/WP.29/GRSP/2014/9). The experts from the Netherlands and France questioned the inclusion of N1 category of vehicles into the UN Regulation since it was not justified by national data. The expert from the United Kingdom supported this conclusion. The expert from EU informed GRSP that a cost benefit analysis by his organization would better identify the category of vehicles to be addressed. GRSP noted that the specifications of the three-dimensional H-point machine (3-D H machine) of the draft UN Regulation differed from those of the 3-D H machine of the Consolidated Resolution No. 3 (R.E.3). The expert from France, supported by the expert from Italy, questioned the reference to the ISO standard, concerning drawings and dummy specifications instead of a reference to an addendum to the M.R.l. Following the suggestion of the expert from the Netherlands, GRSP also noted that a possible development of the UN Regulation (in parallel to the future Phase 2 of the UN GTR No. 14) could be to include the viscous criteria (VC) and the thorax deflection limit. Moreover, GRSP considered GRSP-55-45 incorporating the amendments to ECE/TRANS/WP.29/GRSP/2014/9 agreed during the session.

35. GRSP adopted ECE/TRANS/WP.29/GRSP/2014/9, as amended by Annex VII to this report and ECE/TRANS/WP.29/GRSP/2014/12, not amended, this last introducing a vehicle-to-pole impact speed of 32 ± 1 km/h regardless to the vehicle width. The secretariat was requested to submit ECE/TRANS/WP.29/GRSP/2014/9 as draft UN Regulation on Pole Side Impact and ECE/TRANS/WP.29/GRSP/2014/12 as draft 01 series of amendments to the UN Regulation to WP.29 and AC.1 for consideration and vote at their November 2014 sessions. However, GRSP requested the expert from Australia to send the proposals to WP.29 at its June 2014 session on a preliminary basis and to seek guidance from WP.29/AC.2 on: (i) Reference to ISO STD (WorldSID) instead of an Addendum to M.R.1. and (ii) transitional provisions of the 01 series of amendments simultaneously adopted with the original version of the UN Regulation.

36. Finally, GRSP agreed to seek consent from WP.29 and AC.3 at their June 2014 sessions on mandating an IWG to harmonize the 3-D H point machine specifications.

Proposal for a 01 series of amendments to the proposed new UN Regulation on the approval of vehicles with regard to their pole side impact performance to enable Contracting Parties applying this new regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.

34. The expert from Australia summarized (GRSP-55-16) the work of transposing UN GTR No. 14 (Pole Side Impact) into a draft new UN Regulation (ECE/TRANS/WP.29/GRSP/2014/9). The experts from the Netherlands and France questioned the inclusion of N1 category of vehicles into the UN Regulation since it was not justified by national data. The expert from the United Kingdom supported this conclusion. The expert from EU informed GRSP that a cost benefit analysis by his organization would better identify the category of vehicles to be addressed. GRSP noted that the specifications of the three-dimensional H-point machine (3-D H machine) of the draft UN Regulation differed from those of the 3-D H machine of the Consolidated Resolution No. 3 (R.E.3). The expert from France, supported by the expert from Italy, questioned the reference to the ISO standard, concerning drawings and dummy specifications instead of a reference to an addendum to the M.R.l. Following the suggestion of the expert from the Netherlands, GRSP also noted that a possible development of the UN Regulation (in parallel to the future Phase 2 of the UN GTR No. 14) could be to include the viscous criteria (VC) and the thorax deflection limit. Moreover, GRSP considered GRSP-55-45 incorporating the amendments to ECE/TRANS/WP.29/GRSP/2014/9 agreed during the session.

35. GRSP adopted ECE/TRANS/WP.29/GRSP/2014/9, as amended by Annex VII to this report and ECE/TRANS/WP.29/GRSP/2014/12, not amended, this last introducing a vehicle-to-pole impact speed of 32 ± 1 km/h regardless to the vehicle width. The secretariat was requested to submit ECE/TRANS/WP.29/GRSP/2014/9 as draft UN Regulation on Pole Side Impact and ECE/TRANS/WP.29/GRSP/2014/12 as draft 01 series of amendments to the UN Regulation to WP.29 and AC.1 for consideration and vote at their November 2014 sessions. However, GRSP requested the expert from Australia to send the proposals to WP.29 at its June 2014 session on a preliminary basis and to seek guidance from WP.29/AC.2 on: (i) Reference to ISO STD (WorldSID) instead of an Addendum to M.R.1. and (ii) transitional provisions of the 01 series of amendments simultaneously adopted with the original version of the UN Regulation.

36. Finally, GRSP agreed to seek consent from WP.29 and AC.3 at their June 2014 sessions on mandating an IWG to harmonize the 3-D H point machine specifications.

Explanation of the steps taken to transpose the provisions of GTR No. 14 into a type-approval UN Regulation on pole side-impact protection, including discussion of the scope, impact side, treatment of hydrogen vehicles, and proposal for a 01 series of amendments that would entail a 26 km/h impact speed for narrow vehicles initially before the amendments would bring narrow vehicles into line with other vehicles at 32 km/h.

34. The expert from Australia summarized (GRSP-55-16) the work of transposing UN GTR No. 14 (Pole Side Impact) into a draft new UN Regulation (ECE/TRANS/WP.29/GRSP/2014/9). The experts from the Netherlands and France questioned the inclusion of N1 category of vehicles into the UN Regulation since it was not justified by national data. The expert from the United Kingdom supported this conclusion. The expert from EU informed GRSP that a cost benefit analysis by his organization would better identify the category of vehicles to be addressed. GRSP noted that the specifications of the three-dimensional H-point machine (3-D H machine) of the draft UN Regulation differed from those of the 3-D H machine of the Consolidated Resolution No. 3 (R.E.3). The expert from France, supported by the expert from Italy, questioned the reference to the ISO standard, concerning drawings and dummy specifications instead of a reference to an addendum to the M.R.l. Following the suggestion of the expert from the Netherlands, GRSP also noted that a possible development of the UN Regulation (in parallel to the future Phase 2 of the UN GTR No. 14) could be to include the viscous criteria (VC) and the thorax deflection limit. Moreover, GRSP considered GRSP-55-45 incorporating the amendments to ECE/TRANS/WP.29/GRSP/2014/9 agreed during the session.

35. GRSP adopted ECE/TRANS/WP.29/GRSP/2014/9, as amended by Annex VII to this report and ECE/TRANS/WP.29/GRSP/2014/12, not amended, this last introducing a vehicle-to-pole impact speed of 32 ± 1 km/h regardless to the vehicle width. The secretariat was requested to submit ECE/TRANS/WP.29/GRSP/2014/9 as draft UN Regulation on Pole Side Impact and ECE/TRANS/WP.29/GRSP/2014/12 as draft 01 series of amendments to the UN Regulation to WP.29 and AC.1 for consideration and vote at their November 2014 sessions. However, GRSP requested the expert from Australia to send the proposals to WP.29 at its June 2014 session on a preliminary basis and to seek guidance from WP.29/AC.2 on: (i) Reference to ISO STD (WorldSID) instead of an Addendum to M.R.1. and (ii) transitional provisions of the 01 series of amendments simultaneously adopted with the original version of the UN Regulation.

36. Finally, GRSP agreed to seek consent from WP.29 and AC.3 at their June 2014 sessions on mandating an IWG to harmonize the 3-D H point machine specifications.

Proposal for a new UN Regulation transposing the requirements of the UN Global Technical Regulation on pole side impact (GTR No. 14). This proposal is accompanied by a proposal for a 01 series of amendments (documentGRSP/2014/12) that would enable Contracting Parties applying this Regulation to require a vehicle-to-pole impact speed of 32 ± 1 km/h regardless of the “vehicle width”. This proposal supersedes the earlier version presented in document GRSP/2014/9.

34. The expert from Australia summarized (GRSP-55-16) the work of transposing UN GTR No. 14 (Pole Side Impact) into a draft new UN Regulation (ECE/TRANS/WP.29/GRSP/2014/9). The experts from the Netherlands and France questioned the inclusion of N1 category of vehicles into the UN Regulation since it was not justified by national data. The expert from the United Kingdom supported this conclusion. The expert from EU informed GRSP that a cost benefit analysis by his organization would better identify the category of vehicles to be addressed. GRSP noted that the specifications of the three-dimensional H-point machine (3-D H machine) of the draft UN Regulation differed from those of the 3-D H machine of the Consolidated Resolution No. 3 (R.E.3). The expert from France, supported by the expert from Italy, questioned the reference to the ISO standard, concerning drawings and dummy specifications instead of a reference to an addendum to the M.R.l. Following the suggestion of the expert from the Netherlands, GRSP also noted that a possible development of the UN Regulation (in parallel to the future Phase 2 of the UN GTR No. 14) could be to include the viscous criteria (VC) and the thorax deflection limit. Moreover, GRSP considered GRSP-55-45 incorporating the amendments to ECE/TRANS/WP.29/GRSP/2014/9 agreed during the session.

35. GRSP adopted ECE/TRANS/WP.29/GRSP/2014/9, as amended by Annex VII to this report and ECE/TRANS/WP.29/GRSP/2014/12, not amended, this last introducing a vehicle-to-pole impact speed of 32 ± 1 km/h regardless to the vehicle width. The secretariat was requested to submit ECE/TRANS/WP.29/GRSP/2014/9 as draft UN Regulation on Pole Side Impact and ECE/TRANS/WP.29/GRSP/2014/12 as draft 01 series of amendments to the UN Regulation to WP.29 and AC.1 for consideration and vote at their November 2014 sessions. However, GRSP requested the expert from Australia to send the proposals to WP.29 at its June 2014 session on a preliminary basis and to seek guidance from WP.29/AC.2 on: (i) Reference to ISO STD (WorldSID) instead of an Addendum to M.R.1. and (ii) transitional provisions of the 01 series of amendments simultaneously adopted with the original version of the UN Regulation.

36. Finally, GRSP agreed to seek consent from WP.29 and AC.3 at their June 2014 sessions on mandating an IWG to harmonize the 3-D H point machine specifications.

Draft proposal transposing the provisions of the pole side-impact protection Global Technical Regulation into a UN Regulation as approved by the Working Party on Passive Safety (document GRSP/2014/9, as amended by Annex VII to the report of the 55th GRSP session). This proposal is submitted with a request for guidance on the use of references to an ISO Standard (ISO 15830:2013) instead of preparing an Addendum to the Mutual Resolution No. 1 (M.R.1.) for the WorldSID 50th male specifications.

41. The representative of Australia introduced the draft UN Regulation (WP.29-163-14) as well as a draft 01 series of amendments (WP.29-163-15) to receive guidance (see para. 29 above). He explained that a revised version of WP.29-163-14 would be submitted for consideration and vote to the November 2014 session of WP.29 on appropriately addressing the reference to the ISO standard. He indicated that in the framework of the IWG activities on side impact dummies, work was adequately progressing on including the 50th percentile WorldSID into the draft Addendum 2 to M.R.1. He added that, as a result of recent negotiations, ISO would provide the specifications needed. Therefore, he announced that a draft Addendum 2 would be ready for consideration and vote by the end of 2015 or beginning 2016. The representative of the United States of America confirmed this schedule.

Proposal for an 01 series of amendments to the proposed new UN Regulation on pole side-impact protection (transposing GTR No. 14). This proposal would permit contracting parties to to require a vehicle-to-pole impact speed of 32 ± 1 km/h regardless of the “vehicle width” and is based upon document GRSP/2014/12 and amends the draft PSI regulation as proposed in document WP.29/163/14. The Working Party on Passive Safety approved this proposal provided that Australia would seek guidance on its transitional provisions (since this amendment would, in principle, be adopted at the same time as the original PSI regulation at the November 2014 WP.29 session). This draft incorporates comments from Germany, Japan, and OICA received after the GRSP 55th session.

41. The representative of Australia introduced the draft UN Regulation (WP.29-163-14) as well as a draft 01 series of amendments (WP.29-163-15) to receive guidance (see para. 29 above). He explained that a revised version of WP.29-163-14 would be submitted for consideration and vote to the November 2014 session of WP.29 on appropriately addressing the reference to the ISO standard. He indicated that in the framework of the IWG activities on side impact dummies, work was adequately progressing on including the 50th percentile WorldSID into the draft Addendum 2 to M.R.1. He added that, as a result of recent negotiations, ISO would provide the specifications needed. Therefore, he announced that a draft Addendum 2 would be ready for consideration and vote by the end of 2015 or beginning 2016. The representative of the United States of America confirmed this schedule.

42. WP.29 noted the information by OLA that the legal notification procedure for any amendment to a UN Regulation which was not in force would be initiated only after the entry into force of that UN Regulation. Therefore, WP.29 agreed that the draft 01 series of amendments, even if adopted at its November 2014 session, would await the entry into force of the draft UN Regulation. WP.29 noted that a revised version of WP.29-163-15 would be submitted by Australia, with new transitional provisions in line with the general guidelines ECE/TRANS/WP.29/1044/Rev.1.

Explanatory document on the deliberations and outstanding issues concerning the draft UN Regulation and its proposed 01 series of amendments. These issues concern the references to an ISO standard and transitional provisions for the amendment.

Proposed text transposing GTR No. 14 on pole side impact protection into a UN Regulation under the 1958 Agreement. (A separate proposal for the 01 series of amendments (document WP.29/2014/80) has also been submitted to enable Contracting Parties applying this Regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.)

Proposal for a 01 series of amendments to the proposed new UN Regulation on the approval of vehicles with regard to their pole side impact performance to enable Contracting Parties applying this new regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.

72. On item 4.13.3 (01 series of amendments to the new Regulation on PSI), the secretariat reminded WP.29 delegates that the UN Office of Legal Affairs (OLA) will not initiate the legal procedure for adoption of the 01 series of amendments until the original version of the Regulation on PSI entered into force.

The scope of the new Global Technical Regulation on Pole Side Impact includes vehicles of category N1 (limited to GVM < 3.5 t) and vehicles of category M1 (without mass limit). However, the vehicle fleet includes a small number of M1 vehicles with a GVW > 3.5t which are based on vehicles of category N2, N3, M2 or M3. Therefore, OICA proposes to limit the scope of the GTR to both M1 and N1 vehicles under 3.5 t maximum vehicle mass in order to alleviate burdens on manufacturers producing M1 variants based on N2, N3, M2, or M3 vehicles.

48. The expert from Australia introduced GRSP-56-33 (superseding GRSP-56-12), to clarify the scope of the UN Regulation. GRSP adopted the proposal as reproduced in Annex VII of this report. The secretariat was requested to submit the proposal to WP.29 and AC.1, for consideration and vote at their June 2015 sessions, as draft Supplement 1 to the new UN Regulation on Pole Side Impact.

The scope of the new Global Technical Regulation on Pole Side Impact includes vehicles of category N1 (limited to GVM < 3.5 t) and vehicles of category M1 (without mass limit). However, the vehicle fleet includes a small number of M1 vehicles with a GVW > 3.5t which are based on vehicles of category N2, N3, M2 or M3. Based on the OICA proposal (document GRSP-56-12) and ensuing discussions, Australia proposes to limit the scope of the GTR to both M1 vehicles under 3.5 t maximum vehicle mass and to certain N1 vehicles based on geometric measurements.

48. The expert from Australia introduced GRSP-56-33 (superseding GRSP-56-12), to clarify the scope of the UN Regulation. GRSP adopted the proposal as reproduced in Annex VII of this report. The secretariat was requested to submit the proposal to WP.29 and AC.1, for consideration and vote at their June 2015 sessions, as draft Supplement 1 to the new UN Regulation on Pole Side Impact.

46. The expert from Germany introduced GRSP-56-37 to inform GRSP on the activity concerning the terms of reference and the work plan for the IWG to harmonize the specifications of the three-dimensional H-point machine.

Proposal to limit the scope of UN R135 to M1 vehicles under 3.5 t maximum vehicle mass and to certain N1 vehicles based on geometric measurements. The proposal would exclude the small number of M1 vehicles weighing in excess of 3.5t that are based on N2, N3, M2, or M3 platforms.

Proposal to limit the scope of UN R135 to M1 vehicles under 3.5 t maximum vehicle mass and to certain N1 vehicles based on geometric measurements. The proposal would exclude the small number of M1 vehicles weighing in excess of 3.5t that are based on N2, N3, M2, or M3 platforms. [Because the transitional provisions of the 01 series of amendments to UN R135 stipulate an effective date of 1 September 2016, this supplement to the 01 series will remain pending until after that date. Although adopted, the supplement cannot become enter into force prior to the effective date of the regulation it modifies.]

44. Referring to its December 2014 session (see ECE/TRANS/WP.29/GRSP/56 para. 48), GRSP confirmed its adoption and submission to WP.29 and AC.1, for consideration and vote at their June 2015 sessions, a draft Supplement 1 to the original text of the UN Regulation and a draft Supplement 1 to the 01 series of amendments to the UN Regulation on Pole Side Impact.

39. The expert from Germany, Chair of the IWG on Three-dimensional H-point machine introduced GRSP-57-30 to inform GRSP on the progress of the activity of the IWG. He added that the IWG was not yet in the position of drafting the terms of reference of the group because it was agreed to consult GRSP and WP.29 first. He added that the objective of the IWG would be to prepare an addendum to the Mutual Resolution M.R.1 for the 3-D H-point machine and, therefore, it would be necessary to use detailed information on the 3-D H-point machine, e.g. detailed drawings, which is currently only available in standards of the Society of Automotive Engineers International (SAE Int.). GRSP agreed on the request of the IWG to seek guidance to WP.29 and AC.3 at their June 2015 sessions on how to proceed to receive the above mentioned specifications and drawings from SAE International.