previous meeting next meeting
Berlin
(Latest 23 September 2020)
Agenda
1. Welcome and introduction

The Chair recalled that this meeting would hopefully be one of the last, i.e. some big achievements are expected to be reached at this session.

2. Adoption of the agenda

The agenda was adopted with no change.

3. Approval of the minutes of the previous session

The report was reviewed with minor changes. Some experts deplored that some presentations were not ready [prior to] the meeting.

4. Outcomes of IGPG - 08 ( November 2013 )

The group acknowledged the outcomes of the last session.

5. Proposal for a wiper test
5.1. Outcome of the Subgroup 1 - On-Road-Testing of wiped plastic glazing (real-life-data)

Dr. Matthai, as Pilot for IGPG-task force Wiper-SG1, tabled the presentation IGPG-09-03.

Dr. Buckel pointed out that with a haze of 0.2% in 50,000 cycles, the reality of the field seems less severe than the wiper test.

Dr. Buckel summarized bilateral discussions with Dr. Matthai. Assuming the same initial haze value of 0.1% in the 95% confidence area, the data of Audi show that minor changes in the delta haze are to be expected. Dr. Matthai explained that at her company, they succeeded in having more cycles than the suppliers (up to 50,000). As a summary, plastic glazing shows damage very soon, the Taber test is not relevant for plastic glazing, and some OEMs would reject it.

A debate took place on the possible correlation between mileage and lab wiper cycles. It was also found necessary to avoid a comparison with glass and rather focus on the absolute quality of plastic glazing with regard to safety.

Dr. Matthai stressed that OEMs focus on traffic safety, hence optical distortion for example is an important criterion, in particular when the customer is key for the choice of an OEM with regard to optical qualities. OICA pointed out that the OEM internal quality levels should not influence the discussions on Type Approval regulation.

Evonik was optimistic that products could evolve and suggested to put the number of cycles to 20,000. In addition, it is necessary to compare plastic with plastic (hydrophobic vs. hydrophilic) in order to make a correlation between real road tests and lab tests. Hence the correlation factor for glass cannot be used for plastic. Some experts were convinced that the wiper test is more severe for plastic than for glass, but were lacking data to know how much harder.

SABIC questioned some choices in the test method (e.g. flow of water poured on the test sample).

The spirit of the 1958 Agreement was recalled (i.e. the performance tests in a regulation could only simulate the reality) with UN R94 (frontal impact) and UN R83 (pollutant emissions) taken as examples, and the Secretary stressed that durability was an additional criterion added in the case of resistance to abrasion, and already existing in the case of UN R83 (160,000-km durability test).

The experts were lacking justifications for the values and test method for the wiper test.

Polyplastic proposed that the OEMs focus on the wiper system in addition to the windscreens since the plastic glazing is by nature a hydrophobic material. The group convened that this was out of its mandate, and that progress will happen as from the time the plastic windscreens will be allowed.

Rough evaluation of some key figures:

ExperienceTotal HazeCoatingComments
Number of cyclesNumber of km
20.0006,1%KRD1 sample
150.000< 2,5%KRD
20.000 0,2 – 0,8%Coating BAS4700, Real car (BMW 3-Series)
20.000+/- 1,2%Coating BAS4700
1 million BMS1,2 Coating BAS4700
52.00010.0000,2Coating BAS4700 (Golf)
30008.2000,2%Coating BAS4700 (Golf)

Mr Wiesenberger concluded that the value of 20.000 cycles is more severe than what was experienced in reality.

IGPG-09-03 | IGPG Task Force Wiper Test: On-road tests (Subgroup 1)- Investigation of windshields with standard laminated glass

Proposal for a summary to date:

  • Agreed to:
    • Keep Taber test
    • Add a set of 3 tests as an alternative to Taber test for plastic glazing if the informal group can demonstrate that the set is representative of reality.
    • Comments:
      • Bayer, KRD, Momentive, MPA, Evonik, Polyplastic some OEMs believe the set to be representative
      • Sabic believes the wiper test as shown by SG2 not shown to be representative
      • Final OICA position to be defined
    • Set of 3 tests to be:
      1. Sand drop
      2. Amtec Kistler
      3. Wiper test
    • Wiper test to be finalized with regard to:
      • Test method
      • Number of samples
      • Pass/fail values

    Wiper test method:

    itemvalueComments
    Test conditionsSee document of SG2 (wiper test)
    Measurement machineSee document IGPG-09-04 (IGPG-TF Wipe-SG2) (wiper test): Machine, Wiper blade, Aqueous suspension (with test dust)Wiper blade can be best adapted to the windscreen material.
    Test procedureSee document IGPG-09-04 (IGPG-TF Wipe-SG2) (wiper test) including expression of the results
    Number of cycles[20.000]/[50.000]
    • 20.000 in 3 labs (round robin test). 2 days of testing time; i.e. 3 samples = 6 working days (solution supported by the majority)
    • 50.000 in one lab (supported by some OEMs)
    • OICA to make a position for next meeting
    • Informal document to contain [20.000]
    Number of samples3As in the other tests
    Pass/fail methodHazemeter
    Pass/fail limits[2] / [0,5] % Delta haze
    • Problem of correlation to mileage.
    • Note: hazemeter precision is 0,8 + needs to take account of results distribution. Figure to be confirmed at 10th meeting (June 2014).
    • Considered to be challenging for the coating producers, hence technical progress is expected.
    • 0,5% is supported by some OEMs (50.000 cycles and 0,5% haze).
    • OICA is requested to take a position for June meeting.

    Some experts from the automotive industry were of the opinion that the values of “20,000 cycles” and “2% haze” could not sufficiently guarantee traffic [safety].

5.2. Outcome of the Subgroup 2 - lab test equipment to test wiper resistance on small samples

Dr. Buckel presented the outcomes of subgroup 2. The informal group welcomed the results of the SG2.

The group furthermore reviewed the proposed test method of the wiper test. Some experts proposed that the choice of the wiper blade be optional to the applicant, such that the test best fits the reality. This principle was agreed by all experts and it was agreed that the wording reflects this possibility.

6. Review of the Taber test

The informal group was informed of the ISO 15082 CD ballot with comments from Japan: concerns to introduce plastic material reference samples, and proposed to keep the glass reference samples.

The ISO group mentioned that the behaviours of the two materials are different; hence glass is no good reference for plastic testing. Yet the problem is whether the plastic samples can be produced with good stability along the years. Then the German industry decided to make a test with PC plastic plates coated with AS4000 by 3 different manufacturers, i.e. with different coating machines, to see whether the PC+AS4000 reference material can be reproduced by different suppliers. A Japanese manufacturer might join the group of the German manufacturers (“coaters”) which will produce coated reference plates. Coating will be applied by each coater with thickness of 5 microns and 10 microns (lower and upper limit), 3 samples each. Taber test will be carried out on those samples by MPA and Pilkington in order to get information about the reproducibility of the coated-plastic reference material.

Proposal from Germany to “qualify” the Taber wheels, then use a correction factor (“two-step process”). This was agreed by the ISO meeting. CD ballot just finalized, DIS ballot to start in August 2014. Whatever the amount of comments, the work cannot be finished before the end of the GRSG-IGPG task; i.e. at the best in mid-2015. Draft report of the meeting will be made available. Next ISO meeting scheduled in October 2014.

7. Laminated rigid plastic windscreens

Comments from Dr. Dümmler:

  • Page 3: title should read “Annex 1, Appendix 13"
  • Some improvements were agreed in the wording of the indices of difficulties for the secondary characteristics (page 7) and in in the Taber Test (page 8)

Some further alignments on document 08-02-Rev.1 were adopted. All experts agreed to the document as changed in the meeting.

It was agreed to construct a consolidated document with the 3 existing texts, to be prepared for the 10th meeting of the informal group, then tabled at the 107th session of GRSG (Sept-Oct 2014).

IGPG-08-03 | Proposal for laminated rigid plastic windscreens Working draft proposal for amendments to UN R43 to introduce provisions for the approval of laminated rigid plastic windscreens.
8. Further discussion of the draft regulatory text

Some experts raised that paragraph 6.1.3.4. of Annex 18 should be improved in order not to repeat the exemptions now included in Annex 21 per document GRSG/2014/15. Same was recognized for annex 14.

The experts discussed the inconsistency in the regulation about the wording and interpretation of the “number of test pieces”. Dr. Dümmler pointed out that this problem can be found in Annexes 14, 16, 17, 18, 19.

Current wording of the regulation permits three different interpretations:

  • Samples of 300 × 300 mm,
  • samples cut at 300 × 300 mm from real part or
  • complete Real part.

The experts agreed for a further change in paragraph 5.2. of annexes 17, 18 and 19 (Secretariat to do the work). The Chair committed to inform GRSG on the necessity to amend annexes 14 and 16 as well for consistency. But the group agreed not to propose changes at the forthcoming GRSG session.

GRSG/2014/15 | Proposal for Supplement 3 to the 01 series of amendments to Regulation No. 43 Text prepared by the Informal Group on the Introduction of Plastic Glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43 (IGPG) in order to clarify the requirements of Annex 21 (provisions on the installation of safety glazing on vehicles).
IGPG-08-02/Rev.1 | Draft proposal for amendments to Regulation No. 43 Draft proposal prepared for submission to the Working Party on General Safety to introduce plastic glazing for windscreens and laminated plastic panes other than windscreens into Regulation No. 43.
9. Revision of Annexes 14 and 21

The experts discussed the document from Germany GRSG-106-02. Concerning paragraph 4.2.2.2., the experts acknowledged that the document GRSG-106-02 was developed by the approval authorities and was already covered by the document GRSG/2014/15. The experts agreed to review internally the proposed wording and to ask the German representative, at the 2nd day of the meeting, the origin, and whether withdrawing the document would be feasible.

Note of the Secretariat: This action is still to be conducted.

Mr Veeneman was keen that the group confirms full support to document GRSG/2014/15. The group had no further remark. The document GRSG/2014/15 will be presented by France with the support of the informal group.

GRSG-106-02 | Proposal for an amendment to UN Regulation No. 43 Proposal to introduce provisions for the use of plastic safety glazing in side windows behind the B pillar more in line with the stipulations for glazing with a light transmittance below 70 per cent in that area.
GRSG/2014/15 | Proposal for Supplement 3 to the 01 series of amendments to Regulation No. 43 Text prepared by the Informal Group on the Introduction of Plastic Glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43 (IGPG) in order to clarify the requirements of Annex 21 (provisions on the installation of safety glazing on vehicles).
10. List of action items for next meeting



  • Change in paragraph 5.2. of annex 17, 18, 19 (Secretariat to do the work)
  • Chair to inform GRSG on the necessity to amend annexes 14 and 16 for consistency
  • Consolidated document with the 3 existing texts (Annexes 17, 18, 19) (Secretary and Chair) as an informal document for GRSG-106
  • Paragraph 6.1.3.4. of Annex 18 should be improved in order not to repeat the exemptions now included in Annex 21 per document GRSG/2014/15. Same was recognized for annex 14. The group agreed not to propose changes at the forthcoming GRSG session
  • OICA to have positions with regard to wiper test for June meeting

11. Next meetings

GRSG-106: Geneva, 5-9 May 2014
IGPG-10: Wolfsburg (Autostadt), 17-18 June 2014
GRSG-107: Geneva, 30 Sept – 3 Oct 2014

12. Any other business