Proposal for a new UN Regulation on the approval of devices for reversing motion and motor vehicles with regard to the driver’s awareness of vulnerable road users behind vehicles. The purpose of this Regulation is to provide the provisions for reversing motion concerning on awareness of vulnerable road users proximity. UN Regulation No. 46 provides provisions for indirect vision of motor vehicles. This Regulation expands driver’s vision or awareness for vehicle rear direction when in reversing motion. Therefore, some requirements of this Regulation may be satisfied by devices complying with UN Regulation No. 46.

Proposal in line with ISO 2575 to allow for the use of different colors (e.g., red, yellow, green) to convey the status modes (e.g., failure, active) of seven functions via modification of footnote 18 under Table 1.

Proposal to correct erroneous references (to annexes in the regulation as well as to UN R94 and R95) in the text.

Proposal to update Part III of UN R93 to enable approval of truck cabs where the front underrun protection is integrated in the motor vehicle (in order to improve aerodynamic performance). This proposal would define the forward reference point as being the same transverse location where the force is applied. This results in FUPs where (in the case of cab fronts that are curved) at least 400 mm must be maintained along the front contour of the cab, instead of the foremost point. The proposal includes transitional provisions from 1 September 2020.

Proposal to extract provisions from UN R116 in order to establish a separate regulation for the approval of devices to protect against unauthorized vehicle use. The splitting of UN R116 into three separate regulations has been proposed to advance the implementation of the International Whole Vehicle Type Approval system.

Proposal to extract provisions from UN R116 in order to establish a separate regulation for the approval of immobilizers and vehicles equipped with immobilizers. The splitting of UN R116 into three separate regulations has been proposed to advance the implementation of the International Whole Vehicle Type Approval system.

Proposal for a new regulation on uniform provisions concerning the approval of vehicle alarm systems and approval of a vehicle with regard to its vehicle alarm system. The regulation would extract provisions from UN R116 in order to advance UN R0 on the international whole vehicle type approval system.

Proposal to:

1. clarify that the application of an AECD approval to other vehicle categories than M₁ and N₁ is not mandatory,
2. align the power supply requirement of Part III, para. 34.1 with the corresponding requirement in Part II, para. 25.1.
3. clarify with regard to para. 34.1 that if the vehicle is equipped with both
   • -a “back-power supply” as listed in para. 35.10.1 and
   • -a “Power supply other than back-up power supply mentioned in paragraph 35.10.1” as listed in para. 35.10.2
   both should be tested according to Annex 9. The “Power supply other than back-up power supply mentioned in paragraph 35.10.1” should indeed only be tested if it is the only power supply for the AECS.
4. include two-year transitional provisions
5. remove the exclusion of M₁ and N₁ not equipped with a side airbag and to specify that the AECS shall be able to output the navigation solution in an NMEA-0183 protocol format (RMC, GGA, VTG, GSA and GSV message), among other clarifications.

Proposal to introduce electromagnetic specifications for the approval of an electronic device, such as a transponder — even without the traditional functionality of a mechanical key — under UN R62 via reference to UN R10 on electromagnetic compatibility (as is the case under UN R116).

Proposal from the VRU Proximity Awareness informal group to

1. clarify test procedures allowing non-random selection of parameter combinations and
2. provide for protrusion requirements for Blind Spot Information Systems (BSIS) external elements.

Proposal based on the outcomes of discussions by the GRSG task force on gas-fuelled vehicle regulations to clarify provisions for periodic testing and periodic requalification of Compressed Natural Gas (CNG) cylinders and Liquefied Natural Gas (LNG) tanks.

Proposal to introduce provisions for activation of a “temporary modified view” (such as change in image magnification or resolution) per ISO 16505:2015 to complement the static Class II field of vision using a Camera Monitoring System (CMS).

Proposal to introduce changes/additions in the Change of Design Table to better specify appropriate test requirements for CNG cylinders with composite materials and, in some cases, to harmonize with International Standard Organisation (ISO) standard 11439.

Proposal to add a missing footnote concerning the exemptions for heaters located outside the passenger compartment using water as a transfer medium and to clarify that it is not necessary to apply Annex 4 for the heat pump because the heat transfer fluid does not contain polluting air.

For escape hatches on buses of Classes A and B, proposal to allow a maximum length of 1600 mm equally spaced to cover the shortest vehicles, so the allowed space should be the maximum of either the third of the length or 1600 mm. This proposal will not affect the positioning requirements for any mid-sized and larger buses.

Proposal to enable the use of small indicative lines to assist the driver in discriminating among two or more fields of vision rendered as a combined continuous image on a display.

Proposal to introduce a definition for “Aerodynamic devices” and ensure that such devices shall not compromise the functionality of rear underrun protection devices.

Proposal to exempt Zone I from opaque obscuration requirements of GTR 6 under certain conditions.

Proposal to introduce a generic drawing to improve interpretation of the regulation, especially with regard to contactable parts (sphere protocol). The proposal aims to clarify how to deal with potentially “exempted” parts and which requirements apply to which part of the windscreen wiper. Given the implications for approvals, the proposal is presented as a new series of amendments with transitional provisions starting 24 months after entry into force.

Proposal to enable the approval of the laminated-glass panes with improved mechanical properties.