Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.

Document GRE/2013/62 concerning electronic light source control gear proposed to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. The objective of this proposal is to restrict the voltage at headlamps equipped with (halogen) filament lamp light sources in order to avoid excessively high or low (semi-) permanent luminous intensity of the headlamp and consequently shorter lifetime of the halogen light source. This submission takes into account the positions presented in documents GRE/2013/44, GRE/2013/62, GRE-70-17, and GRE-70-34.

Proposal to delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s) and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the passing and driving beam, using halogen light sources and to harmonize it with the operating voltage requirements in Regulation No. 48.

Proposal to delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens because the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

Document GRE/2014/31 proposes to introduce requirements to avoid intentional non-approved (voltage) variation of the passing and driving beam, using halogen light sources and to harmonize it with the operating voltage requirements in Regulation No. 48. This correction seeks to improve the text by replacing the “about value” for the reference luminous flux with the exact value of 13.2V and to simplify the C.o.P. procedure.

Example of what Regulation No. 112 might look like under the simplification of lighting regulations through the use of a “horizontal reference document” that would consolidate provisions common across lighting regulations.

Proposals for the draft supplements to the 01 series of amendments to Regulation No. 112 and to the 01 series of amendments to Regulation No. 123.

Presentation in support of documents GRE/2014/35 and 2014/36 that would delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. UTAC/France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

Proposal to amend the provisions concerning the heat test requirements for Conformity of Production.