Proposal to allow for the use of natural gas refrigeration systems to vehicles propelled by natural gas (CNG or LNG). This proposal addresses a new, environmentally friendly natural gas fuelled refrigeration system for trucks with refrigerated loads that already are propelled by natural gas. Currently paragraph 18.1.7.1 allows heating systems to be fitted on vehicles to heat the passenger compartment and/or the load area of a vehicle, however, the same provision omits cooling systems that are used on trucks for the carriage of loads requiring refrigeration.

Proposal to correct the definition of “manual valve”, including deletion of the phrase “rigidly fixed to the cylinder or tank”. The definition of the manual valve as part of the accessories fitted to the container or tank (para. 4.16.) is different from the definition specified in paragraph 4.22. The proposed editorial change aims at clarifying the text of these definitions.

Proposal to introduce provisions for cargo-compartment refrigeration systems connected to the compressed natural gas (CNG) and/or liquefied natural gas (LNG) system(s).

Presentation concerning ISO vehicle propulsion energy identification standardization.

Proposal to require in the case where ogive protective covers are fitted to a cylinder that the covers be removed before conducting the impact damage (drop) test.

Proposal to establish a requirement for easy access to the CNG container installation in order to permit visual (periodical) inspection as a means to reduce the safety risks, such as refueling explosion, due to corrosion.

Presentation in support of GRSG/2017/22 (Proposal to harmonize UN R110 with standard ISO 11439:2013 on high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles.)

Proposal for a new series of amendments to UN Regulation No. 110 to improve the specifications for the installation and inspection of CNG cylinders and of LNG tanks and their accessories. This proposal addresses incidents caused by cylinder corrosion. The proposal aims to reinforce the requirements for adequate cylinder protection and for sufficient access to the cylinder and its accessories to allow regular visual inspection.

Rationale for the proposal to harmonize UN R110 with ISO 11439:2013.

Comments from NGV Global on the proposals from Italy (GRSG-112-28) and Germany (GRSG-112-33) regarding the testing and inspection of CNG cylinders.

Proposal to require, in instances where ogive protective covers are fitted to a cylinder, that the covers be removed before conducting the impact damage (drop) test.

Proposal to harmonize the requirements on Compressed Natural Gas (CNG) and/or Liquefied Natural Gas (LNG) vehicles of UN Regulation No. 110 with those of the international standard ISO 11439:2013.

Proposal to correct the definition of “manual valve”, including deletion of the phrase “rigidly fixed to the cylinder or tank”. The definition of the manual valve as part of the accessories fitted to the container or tank (para. 4.16.) is different from the definition specified in paragraph 4.22. The proposed editorial change aims at clarifying the text of these definitions.

Proposal to correct the definition of “manual valve”, including deletion of the phrase “rigidly fixed to the cylinder or tank”. The definition of the manual valve as part of the accessories fitted to the container or tank (para. 4.16.) is different from the definition specified in paragraph 4.22. The proposed editorial change aims at clarifying the text of these definitions.

The proposal also introduces provisions for cargo-compartment refrigeration systems connected to the compressed natural gas (CNG) and/or liquefied natural gas (LNG) system(s).

In the absence of complete harmonization with ISO 11439, this proposal recommends that Table 6.4 of UN R110 should be amended by the following for CNG-1 designs:

1. Delete A.17, A.25, and A.7 since they do not match the tests specified in paragraph 7.5 on Cylinder design qualification tests
2. Add A.15 and A.6 since they do match the tests specified in paragraph 7.5 on Cylinder design qualification tests
3. Add A.24 because paragraph 6.9 on Fire protection requires all PRDs on all cylinder types to comply with A.24.

Proposal to improve provisions for the visual inspection of CNG cylinders, LNG tanks, and their accessories. Germany has proposed (document GRSG-112-33) the prohibition of components or parts of protective housing which must be disassembled during inspection. Italy has proposed (document GRSG-112-28) that visual inspection of cylinders Include access inside any protective covers of the cylinders. Based upon field experience, OICA believes that corrosion damage between support straps, brackets, and pads and the cylinder can be readily identified during visual inspection. Such corrosion requires cylinder replacement. Therefore, OICA proposes clarifications to inspection procedures to address the German and Italian concerns.

Proposal to include transitional provisions for the alignment of UN Regulation No. 110 with ISO 11439:2013 per document GRSG/2017/31.

Proposal for further discussion concerning technical advances in the use of CNG accumulators as an intermediate technology for promoting high, stable pressure in CNG engine injection systems. The CNG accumulator is used to stabilize the gas pressure and to allow engine operation whenever the LNG supply system is not able to deliver fuel. This proposal would define requirements to enable the certification of these components.

Proposal for discussion to enable the certification of CNG compressor components. Due to density and temperature constraints, LNG fuel systems require technologies to warm the LNG fuel to reach temperatures and pressures suitable for the engine. In some configurations, this involves the use of CNG compressors. Therefore, this proposal seeks to enable use of this technology through establishment of requirements to ensure safety.

Proposal to clarify the test procedure to be applied in assessing compliance with the requirement for “compatibility with heat exchange fluids of non-metallic parts” Annex 5Q is part of UN Regulation No. 110. In Annex 4D, the wording “Compatibility with heat exchange fluids” is used but there is no reference to the applicable tests. The proposal clarifies that the “LNG heat exchanger – vaporizer” falls within Annex 5Q. The proposal correspondingly clarifies the general overview Figure 1-2, with all tests from Annex 5, and Table 5.1 in Annex 5.

Proposal to harmonize the requirements for CNG/LNG vehicles under UN R110 with those of the international standard ISO 11439:2013.

Proposal to harmonize the requirements for CNG/LNG vehicles under UN R110 with those of the international standard ISO 11439:2013.